Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2767  Input / Turbine Speed Sensor "B" Circuit No Signal  


DESCRIPTION

The ECM detects the input shaft rotation speed based on the signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) and performs gear ratio control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2767 Input / Turbine Speed Sensor "B" Circuit No Signal 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more and the vehicle speed is approx. 7 km/h (4.3 mph).

2.

The transmission revolution sensor (NIN) value is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NIN) circuit

·

Transmission revolution sensor (NIN)

·

ECM

·

Continuously variable transaxle assembly


Comes on DTC stored

MONITOR DESCRIPTION

The ECM receives a signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) installed in the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the primary pulley speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the primary pulley speed sensor. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C280944E01
0.792,2.958 3.188,3.198 2.396,0.24 10 Transmission Revolution Sensor (NIN) 0.802,2.74 1.125,2.938 0.323,0.198 10 B34 2.313,2.073 2.74,2.302 0.427,0.229 10 NIN- 2.292,1.094 2.719,1.323 0.427,0.229 10 NIN+ 2.75,1.385 3.073,1.583 0.323,0.198 10 2 2.74,2.333 3.063,2.531 0.323,0.198 10 1 5.625,1.24 6.052,1.469 0.427,0.229 10 NIN+ 5.615,2.219 6.042,2.448 0.427,0.229 10 NIN- 5.229,1.385 5.656,1.615 0.427,0.229 10 127 5.823,3 6.25,3.229 0.427,0.229 10 B75 5.813,3.198 6.24,3.427 0.427,0.229 10 ECM 5.219,2.365 5.646,2.594 0.427,0.229 10 128

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (SPD (NIN))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
SPD (NIN)
50003 234 400
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (NIN) Primary pulley speed (NIN) min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition




Data displayed is not as specified under Normal Condition

2.INSPECT TRANSMISSION REVOLUTION SENSOR (RESISTANCE)

Data displayed is as specified under Normal Condition

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (RESISTANCE)
a.
C200614C01
1.281,1.74 1.583,1.219 true 2.188,1.729 1.844,1.208 true 0.115,0.104 0.396,0.333 0.281,0.229 10 *a 1.083,1.792 1.604,2 0.521,0.208 10 NIN+ 2.115,1.792 2.615,2.052 0.5,0.26 10 NIN-
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


Disconnect the transmission revolution sensor (NIN) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

NG

5.INSPECT TRANSMISSION REVOLUTION SENSOR (SENSOR TIP)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)
a.
C267934C16
1.49,0.135 1.938,0.385 0.448,0.25 2.135,1.74 1.781,1.146 true 1.385,1.74 1.719,1.146 true 1.604,0.177 2.063,0.375 0.458,0.198 10 B75 0.969,1.854 1.74,2.083 0.771,0.229 10 127 (NIN+) 1.948,1.854 2.646,2.083 0.698,0.229 10 128 (NIN-) 0.115,0.083 0.385,0.323 0.271,0.24 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-127 (NIN+) - B75-128 (NIN-) 20°C (68°F) 560 to 680 Ω
B75-127 (NIN+) - Body ground Always 10 kΩ or higher
B75-128 (NIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.INSPECT TRANSMISSION REVOLUTION SENSOR (SENSOR TIP)
a.

Remove the transmission revolution sensor (NIN).


b.

Check the sensor tip of the transmission revolution sensor (NIN).

OK:

The sensor tip of the transmission revolution sensor (NIN) is not damaged or contaminated.


HINT:

If the sensor tip of the transmission revolution sensor (NIN) is damaged or contaminated with metal particles, the CVT belt may be damaged.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN)

NG

6.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
6.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT