Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to switch the shift range between "1" (M1 gear) and "7" (M7 gear) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C280943E02
0.875,0.563 3.333,0.906 2.458,0.344 10 to Transmission Shift Switch Assembly (Shift Paddle Switch)*1 0.208,2.906 1.844,3.156 1.635,0.25 10 from ECU-IG NO. 1 Fuse 0.083,3.531 1.792,3.76 1.708,0.229 10 *1: w/ Shift Paddle Switch 0.083,3.948 0.719,4.177 0.635,0.229 10 *2: LHD 0.083,4.344 0.719,4.573 0.635,0.229 10 *3: RHD 2.469,3.74 4.333,4.01 1.865,0.271 10 Transmission Control Switch 2.479,3.531 2.906,3.76 0.427,0.229 10 G36 2.521,1.875 2.771,2.083 0.25,0.208 10 2 2.51,3.073 2.76,3.281 0.25,0.208 10 4 4.094,1.875 4.438,2.146 0.344,0.271 10 3*2 4.083,2.073 4.427,2.344 0.344,0.271 10 1*3 4.083,2.469 4.427,2.74 0.344,0.271 10 1*2 4.083,2.667 4.427,2.938 0.344,0.271 10 3*3 4.104,3.063 4.354,3.271 0.25,0.208 10 5 2.771,1.615 3.198,1.844 0.427,0.229 10 E 2.75,2.792 3.177,3.021 0.427,0.229 10 IG 3.625,1.604 4.052,1.833 0.427,0.229 10 SFTU 3.625,2.188 4.052,2.417 0.427,0.229 10 SFTD 3.833,2.792 4.104,2.99 0.271,0.198 10 S 5.615,1.75 6.042,1.979 0.427,0.229 10 SFTU 5.625,2.333 6.052,2.563 0.427,0.229 10 SFTD 5.635,2.927 5.906,3.125 0.271,0.198 10 S 5.323,1.885 5.573,2.115 0.25,0.229 10 42 5.313,2.458 5.573,2.698 0.26,0.24 10 43 5.302,3.052 5.563,3.271 0.26,0.219 10 41 5.792,4.073 6.219,4.302 0.427,0.229 10 ECM 5.802,3.885 6.229,4.115 0.427,0.229 10 A62

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C251979C12
0.49,1.042 0.844,1.281 0.354,0.24 2.156,1.802 1.854,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 2.156,1.854 2.365,2.042 0.208,0.188 10 IG 0.542,1.083 0.885,1.302 0.344,0.219 10 G36
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
G36-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)

NG

CHECK POWER SOURCE CIRCUIT

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)
a.
C251979C13
0.49,1.042 0.844,1.281 0.354,0.24 1.313,1.802 1.594,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *a 0.552,1.083 0.896,1.302 0.344,0.219 10 G36 1.219,1.854 1.427,2.042 0.208,0.188 10 E
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G36-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.

Disconnect the transmission control switch connector.


b.
C251980C11
0.865,1.708 1.302,1.281 true 1.271,1.844 1.51,1.281 true 1.719,1.708 1.719,1.281 true 2.167,1.844 1.927,1.292 true 2.542,1.708 2.146,1.281 true 0.125,0.094 0.438,0.292 0.313,0.198 10 *A 0.75,1.771 0.906,1.969 0.156,0.198 10 S 1.177,1.917 1.375,2.073 0.198,0.156 10 IG 1.573,1.771 1.958,1.979 0.385,0.208 10 SFTU 2.198,1.917 2.375,2.083 0.177,0.167 10 E 2.469,1.771 2.854,1.979 0.385,0.208 10 SFTD 0.792,0.469 1.104,0.667 0.313,0.198 10 *a
*A for LHD
*a Component without harness connected
(Transmission Control Switch)


for LHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



c.
C251980C14
0.865,1.708 1.302,1.281 true 1.271,1.844 1.51,1.281 true 1.719,1.708 1.719,1.281 true 2.167,1.844 1.927,1.292 true 2.542,1.708 2.146,1.281 true 0.125,0.094 0.438,0.292 0.313,0.198 10 *A 0.75,1.771 0.906,1.969 0.156,0.198 10 S 1.177,1.917 1.375,2.073 0.198,0.156 10 IG 1.573,1.771 1.958,1.979 0.385,0.208 10 SFTD 2.198,1.917 2.375,2.083 0.177,0.167 10 E 2.469,1.771 2.854,1.979 0.385,0.208 10 SFTU 0.792,0.469 1.104,0.667 0.313,0.198 10 *a
*A for RHD
*a Component without harness connected
(Transmission Control Switch)


for RHD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C277060C02
1.531,0.167 1.896,0.427 0.365,0.26 2.792,1.833 2.313,1.167 true 2.042,1.802 2.229,1.167 true 1.365,1.823 2.063,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 *a 1.604,0.208 1.917,0.406 0.313,0.198 10 A62 2.594,1.896 3.365,2.115 0.771,0.219 10 43 (SFTD) 1.74,1.896 2.51,2.115 0.771,0.219 10 42 (SFTU) 1.094,1.896 1.594,2.094 0.5,0.198 10 41 (S)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-41 (S) - Body ground
·

Ignition switch ON

·

Shift lever in M, "+" or "-"


11 to 14 V
A62-41 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in M, "+" or "-"


Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the spiral cable sub-assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-42 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
A62-43 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
A62-42 (SFTU) - Body ground Shift lever in M 10 kΩ or higher
A62-43 (SFTD) - Body ground Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT




NEXT