Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) J

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result
w/o Entry and Start System
w/ Entry and Start System




w/o Entry and Start System

2.READ VALUE USING GTS (STARTER SIGNAL)

w/ Entry and Start System

14.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK ST RELAY (POWER SOURCE)
3.CHECK ST RELAY (POWER SOURCE)
a.
A296486C04
0.083,0.073 0.396,0.229 0.313,0.156 10 *1 2.104,3.479 2.417,3.635 0.313,0.156 10 *2
*1 No. 2 Engine Room Relay Block Assembly
*2 ST Relay


Remove the ST relay from the No. 2 Engine Room Relay Block Assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ST relay terminal 2 - Body ground Engine cranking 11 to 14 V


HINT:

The engine does not crank because the relay is not installed.


Result:
Proceed to
OK
NG (for Manual Transaxle)
NG (for Automatic Transaxle)




OK

4.INSPECT RELAY (ST RELAY)

NG (for Manual Transaxle)

6.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)

NG (for Automatic Transaxle)

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPLACE RELAY (ST RELAY)

5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Result
OK (for Manual Transaxle)
OK (for Automatic Transaxle)
NG



OK (for Automatic Transaxle)

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH)

OK (for Manual Transaxle)

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH PEDAL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
ST relay terminal 2 - A4-1 Always Below 1 Ω
ST relay terminal 2 or A4-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
ST relay terminal 2 - F2-1 Always Below 1 Ω
ST relay terminal 2 or F2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Result
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G4-2 (ST2) - A4-2 Always Below 1 Ω
G4-2 (ST2) or A4-2 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G4-2 (ST2) - F2-2 Always Below 1 Ω
G4-2 (ST2) or F2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - ST relay terminal 2 Always Below 1 Ω
A62-22 (STA) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G4-2 (ST2) - B36-4 (B) Always Below 1 Ω
G4-2 (ST2) - B77-63 (NSW) Always Below 1 Ω
G4-2 (ST2) or B36-4 (B) or B77-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

14.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG (for Automatic Transaxle)
NG (for Manual Transaxle)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG (for Automatic Transaxle)

15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG (for Manual Transaxle)

18.INSPECT CLUTCH START SWITCH ASSEMBLY
15.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Result
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

NG

16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the No. 2 engine room relay block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-9 (L) - ST relay terminal 2 Always Below 1 Ω
A62-22 (STA) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY, ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-5 (STAR) - B36-4 (B) Always Below 1 Ω
G82-5 (STAR) - B77-63 (NSW) Always Below 1 Ω
G82-5 (STAR) or B36-4 (B) or B77-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Result
OK
NG




OK

19.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY, ST RELAY - ECM)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY, ST RELAY - ECM)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST relay from the No. 2 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A4-1 - A62-22 (STA) Always Below 1 Ω
A4-1, ST relay terminal 2 or A62-22 (STA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F2-1 - A62-22 (STA) Always Below 1 Ω
F2-1, ST relay terminal 2 or A62-22 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the clutch start switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G82-5 (STAR) - A4-2 Always Below 1 Ω
G82-5 (STAR) or A4-2 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G82-5 (STAR) - F2-2 Always Below 1 Ω
G82-5 (STAR) or F2-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR