Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0560  System Voltage  


MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage An open in the ECM back up power source circuit (1 trip detection logic).
·

Open in back up power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

ECM power source Below 3.5 V
Stand-by RAM Initialized

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A300175E02
1.75,1.146 2.729,1.375 0.979,0.229 10 false FL MAIN 0.854,2.667 1.833,2.896 0.979,0.229 10 false Battery 3.635,1.146 4.729,1.385 1.094,0.24 10 false EFI-MAIN NO.1 5.844,2.073 6.823,2.302 0.979,0.229 10 false E1 5.833,0.875 6.813,1.104 0.979,0.229 10 false BATT 6.135,3.063 6.698,3.292 0.563,0.229 10 false ECM 5.479,0.969 6.042,1.198 0.563,0.229 10 false A62 5.49,2.063 6.052,2.292 0.563,0.229 10 false B77 5.563,0.781 6.125,1.01 0.563,0.229 10 false 1 5.531,1.875 6.094,2.104 0.563,0.229 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Inspect that the battery is not depleted.

Click herePower Source / Network>2AR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

NG

REPAIR OR REPLACE BATTERY TERMINAL

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A255690C38
0.417,0.844 0.906,1.135 0.49,0.292 1.458,1.125 0.958,1.615 false 0.135,0.104 0.302,0.281 0.167,0.177 10 *a 0.531,0.917 0.875,1.115 0.344,0.198 10 A62 0.573,1.594 0.969,1.823 0.396,0.229 10 BATT
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Wait 5 seconds or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0560 is output A
DTC is not output B




A

B