Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE FLUID › 2012.12–2015.10
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0051078 AUTOMATIC TRANSAXLE FLUID N

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The U760F automatic transaxle does not have an oil filler tube or oil level gauge. When adding fluid, add fluid through the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the oil pan.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the transaxle. Ensure that the fluid temperature is as specified and the engine is idling.


c.

The U760F automatic transaxle requires Toyota Genuine ATF WS.


d.

Perform the adjustment according to the following procedures and notes.

C202513E08
1.875,2.333 2.719,2.594 2.719,2.594 2.719,2.708 true 5.625,2.385 6.135,2.656 6.135,2.656 6.135,2.813 false 1.552,3.396 4.271,3.76 2.719,0.365 12 false 3. ADJUST FLUID TEMPERATURE 0.302,5.781 2.25,6.125 1.948,0.344 12 false 4. ADJUST FLUID LEVEL 0.063,0 2.146,0.344 2.083,0.344 12 false Fluid Filling Procedure: 0.063,0.344 2.313,1.073 2.25,0.729 12 false 1. PERFORM INITIAL FILLING (when necessary) 4.021,0.344 7.083,0.573 3.063,0.229 12 false 2. ADD SPECIFIED AMOUNT OF FLUID 0.052,1.083 2.01,1.26 1.958,0.177 10 false Add fluid to the specified level. 4.208,0.792 6.875,1.104 2.667,0.313 10 false Add the correct amount of fluid specified for the operation that was performed. 0.219,2.552 1.542,3.198 1.323,0.646 10 false Add fluid until fluid comes out of the overflow plug hole. 0.146,7.708 1.927,8.708 1.781,1 10 false Keep the overflow plug open until the fluid flow slows and only drops come out. 0.302,6.188 2.688,6.667 2.385,0.479 10 false Drain excess fluid at the specified fluid temperature. 4.281,6.073 6.708,6.719 2.427,0.646 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.542,3.813 6.885,4.552 5.344,0.74 10 false Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 6.365,1.771 7.042,2.323 0.677,0.552 10 false Specified Amount of Fluid 2.094,2.698 3.333,3.302 1.24,0.604 10 false No. 1 Transmission Oil Filler Tube 5.729,2.823 6.635,3.021 0.906,0.198 10 false Overflow Plug


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedures referenced in the work flow below.

C275733E13
0.219,0.979 2.427,1.313 2.208,0.333 10 Operations that require initial filling: 0.292,1.344 3.229,1.625 2.938,0.281 8 Removal and installation of the front drive shaft assembly. 0.292,1.698 1.375,1.969 1.083,0.271 8 Fluid drain and refill. 0.292,2.031 3.052,2.302 2.76,0.271 8 Removal and installation of the air cooled oil cooler. 0.292,2.375 3.292,2.656 3,0.281 8 Removal and installation of the torque converter assembly. 0.292,2.719 3.833,3 3.542,0.281 8 Removal and installation of the transaxle oil pan sub-assembly. 0.292,3.042 3.177,3.333 2.885,0.292 8 Changing the continuously variable transaxle assembly. 3.906,0.979 6.521,1.313 2.615,0.333 10 Operations that do not require initial filling: 3.969,1.313 5.365,1.604 1.396,0.292 8 Repair of a fluid leak, etc. 0.115,0.063 1.146,0.427 1.031,0.365 10 WORK FLOW: 3.396,0.073 3.906,0.375 0.51,0.302 10 START 2.677,0.594 4.531,0.938 1.854,0.344 10 [STEP4] Perform Initial Filling 2.5,3.646 4.792,3.958 2.292,0.313 9 [STEP5] Add Specified Amount of Fluid 2.563,4.219 4.719,4.552 2.156,0.333 10 [STEP6] Adjust Fluid Temperature 1.323,4.698 5.917,5.052 4.594,0.354 10 Enter fluid temperature detection mode and engine idle speed control mode 2.854,5.26 4.396,5.594 1.542,0.333 10 Idling (Warm up the fluid) 3.135,5.802 4.104,6.479 0.969,0.677 10 Check the fluid temperature 2.542,6.646 4.667,6.969 2.125,0.323 10 Fluid level adjustment temperature 1.313,5.979 2.75,6.635 1.438,0.656 10 Below fluid level adjustment temperature 4.198,5.969 5.667,6.635 1.469,0.667 10 Above fluid level adjustment temperature 5.906,5.26 6.99,6.146 1.083,0.885 10 Stop the engine and wait until the fluid temperature drops 2.76,7.229 4.448,7.542 1.688,0.313 10 [STEP7] Adjust Fluid Level 3.031,7.635 4.156,7.938 1.125,0.302 10 Drain excess fluid 2.854,8.208 4.438,8.552 1.583,0.344 10 Check the amount of fluid 2.906,8.896 4.344,9.26 1.438,0.365 10 [STEP8] Rebuild Work 3.469,9.479 3.813,9.719 0.344,0.24 10 END 0.333,8.198 0.917,8.5 0.583,0.302 10 Add fluid 1.292,8.375 2.469,8.688 1.177,0.313 10 No fluid comes out 4.885,8.375 5.958,8.688 1.073,0.313 10 Fluid comes out 6.385,8.188 6.958,8.448 0.573,0.26 10 Overflow 3.969,1.604 6.052,2.188 2.083,0.583 8 Installation of a new transaxle assembly. (with new torque converter assembly)


Hide 3. BEFORE FILLING TRANSAXLE WITH FLUID

a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up.



b.

for Full Cover Type:

Remove the No. 1 engine under cover.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


c.

Remove the rear engine under cover LH.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL


Hide 4. PERFORM INITIAL FILLING

NOTICE:

If the transaxle is hot (ATF temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure (recommended ATF temperature: around 20°C [68°F]).


a.
C205875

Remove the refill plug and gasket from the automatic transaxle assembly.

NOTICE:

After performing any of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the Add Specified Amount of Fluid procedure.


Operations that do not Require Initial Filling
·

Disconnection of the oil cooler tube or oil cooler hose

·

Repair of a fluid leak due to a loose case plug, or a faulty plug gasket or O-ring

·

Installation of a new transaxle with torque converter clutch (parts pre-filled with fluid)




b.
C205876

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the automatic transaxle assembly.

NOTICE:
·

If ATF comes out after removing the overflow plug, wait until the fluid flow slows and only drops come out.

·

If ATF comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




c.
C162883C01
0.833,2.625 1.792,2.625 false 0.885,3.49 1.781,3.49 false 0.667,3.167 0.292,4.094 0.292,4.094 1.177,4.094 true 1.833,2.531 2.042,2.688 0.208,0.156 10 *1 1.25,4.01 1.427,4.188 0.177,0.177 10 *a 1.833,3.406 2.031,3.635 0.198,0.229 10 *2
*1 No. 1 Transmission Oil Filler Tube
*2 Hexagon Socket Wrench
*a Overflow Plug Hole


Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the socket hexagon wrench into the overflow plug hole.



d.

Perform initial filling.

i.
C205877

Fill the transaxle through the refill hole until fluid begins to trickle out of the overflow plug hole.

NOTICE:

Use Toyota Genuine ATF WS.




e.
C205878

Wait until the fluid flow slows and only drops come out.


f.
C205876

Temporarily install the overflow plug.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.

Fill the transaxle with the correct amount of fluid as listed in the table below.

NOTICE:

The refill amount differs depending on the operation that was performed.


Standard Capacity:
Operation Performed Fill Amount
·

Disconnection of the oil cooler tube or oil cooler hose

·

Repair of a fluid leak due to a loose case plug, or a faulty plug gasket or O-ring

·

Installation of a new transaxle with torque converter clutch (parts pre-filled with fluid)


0.5 liters (0.5 US qts, 0.4 Imp. qts)
·

Removal and installation of the drive shaft

·

Removal and installation of the transaxle case oil seal

·

Removal and installation of the oil pan


2.7 liters (2.9 US qts, 2.4 Imp. qts)
Removal and installation of the valve body 3.2 liters (3.4 US qts, 2.8 Imp. qts)
Removal and installation the transaxle (a new torque converter clutch) 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Changing the transaxle (torque converter clutch reused) 3.5 liters (3.7 US qts, 3.1 Imp. qts)
Changing the transaxle (a new torque converter clutch) 5.1 liters (5.4 US qts, 4.5 Imp. qts)



b.
C205875

Temporarily install the refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket. The plug will be removed again to adjust the fluid level.



c.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE

a.

When using the GTS:

HINT:

The actual ATF temperature can be checked on the Data List using the GTS.


i.

Connect the GTS to the DLC3 with the ignition switch off.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



iii.

Enter the following menus: Powertrain / ECT / Active Test / Connect the TC and TE1.

Powertrain > ECT > Active Test
Tester Display
Connect the TC and TE1
50004 64 13

iv.

Enter the following menu: Connect the TC and TE1 / ON.


v.

Enter the following menu: A/T Oil Temperature 1.


vi.

Check the ATF temperature.

NOTICE:
·

If the fluid temperature is below 45°C (113°F), proceed to the next step (recommended ATF temperature: less than 40°C [104°F]).

·

If the fluid temperature is higher than 45°C (113°F), turn the ignition switch off and wait until the fluid temperature drops below 40°C (104°F).




vii.

Depress and hold the brake pedal.


viii.

Start the engine.


ix.

Slowly move the shift lever from P to D, then back to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transaxle.



x.
C278978

While observing the D shift indicator in the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter the fluid temperature detection mode.



xi.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When the fluid temperature detection mode is activated, the D shift indicator in the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the step where the Active Test "Connect the TC and TE1" is first turned on and perform the procedure again.




xii.

Move the shift lever from N to P.


xiii.

Release the brake pedal.


xiv.

Enter the following menu: Connect the TC and TE1 / OFF.

NOTICE:

Be sure that the Active Test "Connect the TC and TE1" is not turned on. If the Active Test is on, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Turning off the Active Test "Connect the TC and TE1" activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or higher and the engine speed is maintained at approximately 800 rpm.

·

Even after the Active Test "Connect the TC and TE1" is turned off, the fluid temperature detection mode is active until the ignition switch is turned off.




xv.

Warm up the engine with the engine idling until the fluid temperature reaches the normal operating temperature (40 to 45°C [104 to 113°F]).

Below Normal Operating Temperature Normal Operating Temperature Above Normal Operating Temperature
Less than 40°C
(Less than 104°F
40 to 45°C
(104 to 113°F)
Higher than 45°C
(Higher 113°F)

NOTICE:
·

If the fluid temperature is within the normal operating temperature range, immediately proceed to the Adjust Fluid Level procedure.

·

If the fluid temperature is higher than 45°C (113°F), stop the engine and wait until the fluid temperature drops to less than 40°C (104°F). Then perform the Adjust Fluid Temperature procedure again from the beginning.



HINT:

In the fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.


D Shift Indicator
Below Normal Operating Temperature
(Less than 40°C)
(Less than 104°F)
Normal Operating Temperature
(40 to 45°C)
(104 to 113°F)
Above Normal Operating Temperature
(Higher than 45°C)
(Higher than 113°F)
Off On Blinks



b.

When not using the GTS:

i.
C166029C54
1.594,0.906 1.792,0.365 1.792,0.365 1.896,0.365 false 1.771,1.49 1.646,1.854 1.646,1.854 1.531,1.854 false 1.313,1.771 1.552,1.948 0.24,0.177 10 TC 1.938,0.281 2.302,0.458 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.

SST
09843-18040  


ii.

Depress and hold the brake pedal.


iii.

Start the engine.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.


HINT:

The indicator lights in the combination meter blink to indicate the DTC output when terminals TC and CG are connected.



iv.

Slowly move the shift lever from P to D, then back to P.

HINT:

Slowly move the shift lever to circulate the fluid through each part of the transaxle.



v.
C278978

While observing the D shift indicator in the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter the fluid temperature detection mode.



vi.

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When the fluid temperature detection mode is activated, the D shift indicator in the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the step where terminal 13 (TC) and 4 (CG) is first connected and perform the procedure again.




vii.

Move the shift lever from N to P.


viii.

Release the brake pedal.


ix.
C166029C54
1.594,0.906 1.792,0.365 1.792,0.365 1.896,0.365 false 1.771,1.49 1.646,1.854 1.646,1.854 1.531,1.854 false 1.313,1.771 1.552,1.948 0.24,0.177 10 TC 1.938,0.281 2.302,0.458 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a
*a DLC3


Remove SST from terminals 13 (TC) and 4 (CG).

NOTICE:

Be sure that terminals TC and CG are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals TC and CG activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature becomes 35°C (95°F) or higher and the engine speed is maintained at approximately 800 rpm.

·

Even after terminals TC and CG are disconnected, the fluid temperature detection mode is active until the ignition switch is turned off.




x.

Allow the engine to idle until the D shift indicator comes on again.

D Shift Indicator
Below Normal Operating Temperature
(Less than 40°C)
(Less than 104°F)
Normal Operating Temperature
(40 to 45°C)
(104 to 113°F)
Above Normal Operating Temperature
(More than 45°C)
(More than 113°F)
Off On Blinks

NOTICE:
·

If the D shift indicator is on, immediately proceed to the Adjust Fluid Level procedure.

·

If the D shift indicator blinks, stop the engine and wait until the fluid temperature drops to 40°C (104°F) or less (the indicator goes off). Then perform the Adjust Fluid Temperature procedure again from the beginning.



HINT:
·

In the fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The Adjust Fluid Level procedure should be performed when the D shift indicator is on (the fluid temperature is within the normal operating temperature range).





Hide 7.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up.



b.

Adjust the fluid level.

i.
C205876

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



ii.

Check the amount of fluid that comes out of the overflow plug hole.

·

If the amount of fluid that comes out of the overflow plug hole is large, proceed to *1.

·

If no fluid comes out of the overflow plug hole, proceed to *2.


NOTICE:

If only a small amount of fluid (approximately 1 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This condition is not considered as overflow, so it is necessary to add fluid.



iii.
C205880

*1:

If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drops come out.


iv.
C205877

*2:

If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid into the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drops come out.

NOTICE:

Use Toyota Genuine ATF WS.



v.
C205878

Check that the fluid flow has slowed and only drops come out.

HINT:

The fluid flow will not completely stop because the fluid expands as its temperature increases.




c.
C205876

Install a new gasket and the overflow plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.
C205875

Install a new gasket and the refill plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


e.

Lower the vehicle.


f.

Turn the ignition switch off.

HINT:

Turning the ignition switch off exits the fluid temperature detection mode.



g.

Disconnect the GTS from the DLC3 (when using the GTS).


Hide 8. REBUILD WORK

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the rear engine under cover LH.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION


e.

for Full Cover Type:

Install the No. 1 engine under cover.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION


f.

Lower the vehicle.