The main body ECU (multiplex network body ECU) receives switch signals from the power window regulator master switch assembly, door control switch assembly, driver door key cylinder lock or unlock switch signals from the front door lock assembly RH*1 or front door lock assembly LH*2. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
*1: for RHD
*2: for LHD
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All doors cannot be locked by power window regulator master switch assembly | A |
| All doors cannot be locked by door control switch assembly (w/ Door Control Switch Assembly) | B |
| All doors cannot be locked by driver door key cylinder | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock SW-Lock | Door control switch (power window regulator master switch assembly) lock signal | ON or OFF | ON: Lock side of door control switch (power window regulator master switch assembly) pushed
OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| Door Lock SW-Unlock | Door control switch (power window regulator master switch assembly) unlock signal | ON or OFF | ON: Unlock side of door control switch (power window regulator master switch assembly) pushed
OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed |
- |
| Tester Display |
|---|
| Door Lock SW-Lock |
| Door Lock SW-Unlock |
The GTS indicates ON or OFF according to the switch operation shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the Techstream.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock SW-Lock | Door control switch assembly lock signal | ON or OFF | ON: Lock side of door control switch assembly pushed
OFF: Lock side of door control switch assembly not pushed |
- |
| Door Lock SW-Unlock | Door control switch assembly unlock signal | ON or OFF | ON: Unlock side of door control switch assembly pushed
OFF: Unlock side of door control switch assembly not pushed |
- |
| Tester Display |
|---|
| Door Lock SW-Lock |
| Door Lock SW-Unlock |
The GTS indicates ON or OFF according to the switch operation shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
NG
for LHD:
Remove the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL
Inspect the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION
for RHD:
Remove the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL
Inspect the power window regulator master switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J5-2 (L) - G78-9 (L1) | Always | Below 1 Ω |
| J5-9 (UL) - G78-10 (UL1) | ||
| J5-1 (E) - Body ground | ||
| J5-2 (L) or G78-9 (L1) - Body ground | Always | 10 kΩ or higher |
| J5-9 (UL) or G78-10 (UL1) - Body ground |
for RHD
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I5-2 (L) - G78-9 (L1) | Always | Below 1 Ω |
| I5-8 (UL) - G78-10 (UL1) | ||
| I5-9 (E) - Body ground | ||
| I5-2 (L) or G78-9 (L1) - Body ground | Always | 10 kΩ or higher |
| I5-8 (UL) or G78-10 (UL1) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Key SW-Lock | Driver door key-linked lock/unlock switch lock signal | ON or OFF | ON: Driver door key cylinder turned to lock position
OFF: Driver door key cylinder not turned to lock position |
- |
| Door Key SW-Unlock | Driver door key-linked lock/unlock switch unlock signal | ON or OFF | ON: Driver door key cylinder turned to unlock position
OFF: Driver door key cylinder not turned to unlock position |
- |
| Tester Display |
|---|
| Door Key SW-Lock |
| Door Key SW-Unlock |
The GTS indicates ON or OFF according to the key cylinder operation shown in the table.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG
Remove the door control switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL
Inspect the door control switch assembly.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Disconnect the I11 door control switch assembly connector.
Disconnect the J5 power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I11-4 (L) - G78-9 (L1) | Always | Below 1 Ω |
| I11-2 (UL) - G78-10 (UL1) | ||
| I11-3 (E) - Body ground | ||
| I11-4 (L) or G78-9 (L1) - Body ground | Always | 10 kΩ or higher |
| I11-2 (UL) or G78-10 (UL1) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
NG
for LHD:
Remove the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for RHD:
Remove the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD (w/ Door Control Switch Assembly)
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-9 (L) - G78-11 (L2) | Always | Below 1 Ω |
| J10-10 (UL) - G78-24 (UL3) | ||
| J10-7 (E) - Body ground | ||
| J10-9 (L) or G78-11 (L2) - Body ground | Always | 10 kΩ or higher |
| J10-10 (UL) or G78-24 (UL3) - Body ground |
for LHD (w/o Door Control Switch Assembly)
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-9 (L) - G78-11 (L2) | Always | Below 1 Ω |
| J10-10 (UL) - G78-12 (UL2) | ||
| J10-7 (E) - Body ground | ||
| J10-9 (L) or G78-11 (L2) - Body ground | Always | 10 kΩ or higher |
| J10-10 (UL) or G78-12 (UL2) - Body ground |
for RHD
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I10-6 (L) - G78-11 (L2) | Always | Below 1 Ω |
| I10-5 (UL) - G78-12 (UL2) | ||
| I10-8 (E) - Body ground | ||
| I10-6 (L) or G78-11 (L2) - Body ground | Always | 10 kΩ or higher |
| I10-5 (UL) or G78-12 (UL2) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG