Home › Engine / Hybrid System › 2AR-FE EMISSION CONTROL › CANISTER(w/ Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008398 2AR-FE EMISSION CONTROL _0055002 CANISTER(w/ Canister Pump Module) A

2AR-FE EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


PROCEDURE

Hide 77641A 2.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A293408N01
2.042,1.813 2.198,2.01 0.156,0.198 10 A

Remove the nut, 3 clips and No. 1 fuel tank protector.

HINT:

The clip labeled A cannot be removed from the No. 1 fuel tank protector.



Hide 77740 3.REMOVE CHARCOAL CANISTER ASSEMBLY

a.
A293407C01
0.802,1.146 1.417,1.146 true 2.302,1.229 2.594,1.51 true 1.542,1.552 1.542,1.375 1.542,1.375 1.813,1.042 true 1.375,2.75 1.375,2.604 1.375,2.604 1.135,2.51 false 2.438,2.073 2.667,2.073 2.667,2.073 2.76,2.323 true 0.625,1.073 0.792,1.25 0.167,0.177 10 true *1 2.552,1.531 2.74,1.698 0.188,0.167 10 true *2 1.469,1.594 1.667,1.781 0.198,0.188 10 true *3 0.542,2.083 0.854,2.24 0.313,0.156 10 false *a 2.146,2.688 2.458,2.844 0.313,0.156 10 false *b 2.281,2 2.594,2.198 0.313,0.198 10 false *4 1.281,2.76 1.594,2.958 0.313,0.198 10 false *4
*1 Vent Line Hose
*2 Air Inlet Line Hose
*3 Purge Line Hose
*a Pull Out
*b Push


Disconnect the connector.


b.

Slide the clamp and disconnect the purge line hose.


c.

Disconnect the air inlet line hose.

i.

Push in the retainer and pull out the air inlet line hose straight from the pipe.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the canister and around the hose. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the charcoal canister assembly and hose.

·

When disconnecting the hose, make sure that the retainer is not lifted.





d.

Disconnect the vent line hose.

i.

Pinch the retainer and then raise it.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the charcoal canister assembly and around the hose. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the charcoal canister assembly and hose.





e.
A293779

Remove the 4 bolts, clip and charcoal canister assembly.


Hide 77751 4.REMOVE CHARCOAL CANISTER BASE BRACKET

a.
A293410

Detach the claw and remove the charcoal canister base bracket.


Hide 77765 5.REMOVE CHARCOAL CANISTER PROTECTOR

a.
A293409

Detach the claw and remove the charcoal canister protector.


Hide 77740Q 6.REMOVE CANISTER PUMP MODULE

a.

Before removing the canister pump module, clean the canister by blowing air into it to ensure that the canister is free of foreign matter.

NOTICE:
·

Make sure to clean the canister using only air.


·

Do not use gasoline, thinners or solvents.




b.
A263349C01
1.354,1.521 2.385,1.865 2.385,1.865 2.635,1.865 true 2.677,1.792 2.99,1.948 0.313,0.156 10 *1
*1 Protective Tape


While disengaging the 2 claws as shown in the illustration, push the canister pump module upwards using a screwdriver to remove it.

HINT:

Tape the screwdriver tip before use.



c.
A263350

Check if the canister contains foreign matter such as mud or water.

i.

Visually check that the inside of the canister is free of foreign matter.


ii.

Hold the canister upside down to make sure that the canister is free of foreign matter.

If the charcoal canister assembly contains foreign matter, replace the charcoal canister assembly.