1. DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
4.DRAIN FUEL
5.DISCONNECT PARKING BRAKE CABLE
Remove the 2 bolts and disconnect the parking brake cable.
50819
6.REMOVE FRONT FLOOR COVER
Remove the bolt and nut.
Detach the 4 clips and remove the front floor cover.
77641A
7.REMOVE NO. 1 FUEL TANK PROTECTOR
58398F
8.REMOVE NO. 1 FLOOR UNDER COVER
Detach the clip and remove the 2 nuts and No. 1 floor under cover.
77209D
9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel pipe.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION
77019J
10.DISCONNECT FUEL TANK TO CANISTER TUBE SUB-ASSEMBLY
Disconnect the fuel tank to canister tube sub-assembly.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION
77276
11.REMOVE FUEL HOSE PROTECTOR
Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.
77213E
12.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank.
77404
13.DISCONNECT FUEL TANK VENT HOSE SUB-ASSEMBLY
Detach the hose clamp and fuel tank vent hose sub-assembly.
77202
14.DISCONNECT BREATHER TUBE SUB-ASSEMBLY
Disconnect the breather tube sub-assembly from the fuel tank filler pipe.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION
77100
15.REMOVE FUEL TANK ASSEMBLY
Disconnect the connector and detach the 3 wire harness clamps.
Using an engine lifter and attachments, support the fuel tank assembly.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly.
Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.
Remove the 2 bolts and No. 2 fuel tank band sub-assembly.
Slightly lower the engine lifter.
Be careful not to cut the wiring.
Disconnect the fuel pump connector and sender gauge connector.
Before this procedure, check the connector for dirt, mud or other contamination.
Do not use any tools in this procedure.
Detach the wire harness from the 3 clamps and remove the fuel tank assembly.
77209D
16.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
77168A
17.REMOVE FUEL TANK VENT TUBE SET PLATE
18.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP
83320
19.REMOVE FUEL SENDER GAUGE ASSEMBLY
77209D
20.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Fuel Tank Main Tube Sub-assembly |
| *2 | No. 3 Fuel Tube Clamp |
| *3 | No. 5 Fuel Tube Clamp |
| *4 | Fuel Tube Grommet |
Detach the 5 clamps and remove the fuel tank main tube sub-assembly.
77289B
21.REMOVE NO. 3 FUEL TUBE CLAMP
Remove the No. 3 fuel tube clamp from the fuel tank assembly.
77299A
22.REMOVE NO. 5 FUEL TUBE CLAMP
Remove the No. 5 fuel tube clamp from the fuel tank assembly.
77295D
23.REMOVE FUEL TUBE GROMMET
Remove the 3 fuel tube grommets from the fuel tank assembly.
77202
24.REMOVE BREATHER TUBE SUB-ASSEMBLY
Disconnect the quick connector and remove the breather tube sub-assembly from the fuel tank assembly.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/ Canister Pump Module)>PRECAUTION
77643A
25.REMOVE NO. 3 FUEL TANK PROTECTOR
Remove the No. 3 fuel tank protector from the fuel tank assembly.