Home › Drivetrain › EB63F MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL(for RH Side)
RM3090E _52 Drivetrain _009273 EB63F MANUAL TRANSMISSION / TRANSAXLE _0057831 DIFFERENTIAL OIL SEAL(for RH Side) A

EB63F MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 31105H 3.REMOVE TRANSAXLE CASE OIL SEAL

a.
C277915C01
0.573,0.667 0.99,0.656 0.99,0.656 1.667,1.115 false 0.417,0.573 0.729,0.771 0.313,0.198 10 *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, pry out the front transmission case oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 41311R 4.REMOVE FRONT DIFFERENTIAL CASE OIL SEAL

a.
C277916E01
0.667,0.927 0.969,0.927 0.969,0.927 1.083,1.323 false 0.354,0.844 0.813,1.042 0.458,0.198 10 SST

Using SST, remove the front differential case oil seal.

SST
09308-00010  

NOTICE:

Be careful not to damage the differential case.



Hide 41311R 5.INSTALL FRONT DIFFERENTIAL CASE OIL SEAL

a.

Coat the lip of a new front differential case oil seal with MP grease.


b.
C277921C01
0.531,0.365 0.979,0.365 0.979,0.365 1.333,1.51 true 1.104,1.802 0.656,0.365 true 2.708,2.458 3.021,2.656 0.313,0.198 10 false *a 0.115,0.313 0.427,0.51 0.313,0.198 10 false SST
*a 21.5 to 22.5 mm (0.847 to 0.855 in.)


Using SST and a hammer, tap in a new front differential case oil seal to the front transmission case.

SST
09950-70010  09649-17010  (09951-07200)

NOTICE:

Do not damage the front differential case oil seal lip.


Standard depth:

21.5 to 22.5 mm (0.847 to 0.855 in.)



Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new transaxle case oil seal with MP grease.


b.
C277918C01
3.052,2.365 3.24,2.365 3.24,2.365 3.24,1.813 false 2.938,2.552 3.052,2.552 3.052,2.552 3.052,2.229 false 1.271,2.813 1.26,1.833 false 1.26,2.438 0.927,2.448 0.927,2.448 0.917,1.885 false 2.271,2.542 2.583,2.74 0.313,0.198 10 *a 2.635,2.479 3.094,2.677 0.458,0.198 10 SST 1.146,2.865 1.604,3.063 0.458,0.198 10 SST
*a 5.5 to 6.5 mm (0.217 to 0.255 in.)


Using SST and a hammer, tap in a new transaxle case oil seal to the transaxle case.

SST
09710-30050  
09950-70010  (09951-07100)

Standard depth:

5.5 to 6.5 mm (0.217 to 0.255 in.)


NOTICE:

Do not damage the front transaxle case oil seal lip.



Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET

Hide 36100 8.INSTALL TRANSFER ASSEMBLY