Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

·

This DTC is related to the air fuel ratio sensor, although the caption is the oxygen sensor.



The air fuel ratio sensor outputs a voltage* that is proportional to the air fuel ratio. The air fuel ratio sensor output voltage is used to control the air fuel ratio mixture.

The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engine. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and Particulate Matter (PM).

In order to reduce PM, the ECM adjusts the air fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.

When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.

*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.

A264921
5.24,2 5.771,2.521 false 5.052,1.823 5.719,2.01 false 5.177,1.417 5.688,1.365 false 5.406,1.302 5.729,1.125 false 5.208,1.76 5.719,2.01 false 3.115,2.063 3.75,1.719 false 2.958,2.104 2.24,1.74 false 2.583,2.625 2.708,2.823 0.125,0.198 10 false A 3.271,2.625 3.396,2.802 0.125,0.177 10 false A 1.677,1.615 2.25,1.813 0.573,0.198 10 false Element 0.677,2.063 1.552,2.281 0.875,0.219 10 false Exhaust Gas 4.875,2.667 5.635,2.865 0.76,0.198 10 false A-A Section 5.74,1.927 6.969,2.146 1.229,0.219 10 false Platinum Electrode 3.813,1.635 4.229,1.813 0.417,0.177 10 false Cover 5.802,2.448 6.094,2.646 0.292,0.198 10 false Air 5.76,0.958 6.219,1.135 0.458,0.177 10 false Heater 5.729,1.219 6.927,1.604 1.198,0.385 10 false Solid Electrolyte (Zirconia Element) 0.354,4.656 1.604,4.938 1.25,0.281 10 false AF Lambda B1S1 0.333,5.958 1.563,6.125 1.229,0.167 10 false AFS Voltage B1S1 1.99,4.729 2.156,4.938 0.167,0.208 10 false 1 1.99,4.198 2.156,4.406 0.167,0.208 10 false 2 2,6.094 2.167,6.302 0.167,0.208 10 false 1 2,6.635 2.167,6.844 0.167,0.208 10 false 0 1.99,5.25 2.156,5.458 0.167,0.208 10 false 0 2,5.573 2.167,5.781 0.167,0.208 10 false 2 2.26,5.552 2.49,5.802 0.229,0.25 10 false (V) 2.885,6.844 3.135,7.094 0.25,0.25 10 false 10 3.198,6.927 3.552,7.177 0.354,0.25 10 false 14.5 3.646,6.844 3.896,7.094 0.25,0.25 10 false 20 4.417,6.844 4.667,7.094 0.25,0.25 10 false 30 5.188,6.844 5.438,7.094 0.25,0.25 10 false 40 5.948,6.844 6.198,7.094 0.25,0.25 10 false 50 0.188,2.979 2.625,3.156 2.438,0.177 10 false Air Fuel Ratio Displayed on the GTS: 3.646,7.125 4.583,7.323 0.938,0.198 10 false Air Fuel Ratio 4.052,4.854 6.677,5.167 2.625,0.313 10 false AF Lambda B1S1 = Air Fuel Ratio / 14.5 2.219,7.802 2.635,7.99 0.417,0.188 10 false 0.060 4.635,7.802 5.052,7.99 0.417,0.188 10 false 0.508 5.229,7.802 5.646,7.99 0.417,0.188 10 false 0.787 5.833,7.802 6.25,7.99 0.417,0.188 10 false 0.978 6.385,7.802 6.802,7.99 0.417,0.188 10 false 1.373 4.031,7.802 4.448,7.99 0.417,0.188 10 false 0.356 3.427,7.802 3.844,7.99 0.417,0.188 10 false 0.268 2.833,7.802 3.25,7.99 0.417,0.188 10 false 0.170 1.729,7.802 1.917,7.99 0.188,0.188 10 false 0 1.656,8.833 1.99,9.021 0.333,0.188 10 false 14.5 5.896,8.833 6.229,9.021 0.333,0.188 10 false 30 2.302,8.833 2.635,9.021 0.333,0.188 10 false 15 4.698,8.833 5.031,9.021 0.333,0.188 10 false 20 6.5,8.833 6.833,9.021 0.333,0.188 10 false 50 3.5,8.833 3.833,9.021 0.333,0.188 10 false 17 2.906,8.833 3.24,9.021 0.333,0.188 10 false 16 0.531,8.833 1.469,9.031 0.938,0.198 10 false Air Fuel Ratio 4.104,8.833 4.438,9.021 0.333,0.188 10 false 18 5.302,8.833 5.635,9.021 0.333,0.188 10 false 25 1.292,7.781 1.521,7.979 0.229,0.198 10 false (V) 0.458,7.708 1.25,8.031 0.792,0.323 10 false AFS Voltage B1S1 0.49,8.24 1.292,8.573 0.802,0.333 10 false AF Lambda B1S1 1.698,8.333 1.927,8.5 0.229,0.167 10 false 1.0 2.25,8.333 2.594,8.51 0.344,0.177 10 false 1.03 2.854,8.333 3.167,8.531 0.313,0.198 10 false 1.10 3.427,8.333 3.74,8.479 0.313,0.146 10 false 1.17 4.073,8.333 4.365,8.531 0.292,0.198 10 false 1.24 4.635,8.333 4.948,8.479 0.313,0.146 10 false 1.38 5.25,8.333 5.583,8.49 0.333,0.156 10 false 1.72 5.844,8.333 6.135,8.479 0.292,0.146 10 false 2.07 6.448,8.333 6.771,8.49 0.323,0.156 10 false 3.45 0.375,9.24 0.771,9.427 0.396,0.188 10 false HINT: 0.646,9.469 6.198,9.625 5.552,0.156 10 false AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V. 2,3.677 2.167,3.885 0.167,0.208 10 false 3

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A297976
0.083,0.073 1.615,0.271 1.531,0.198 10 Reference: 0.156,1.156 1.083,1.635 0.927,0.479 10 from EFI MAIN NO. 2 fuse 1.802,2.354 2.448,2.865 0.646,0.51 10 EFI MAIN NO. 2 3.354,2.021 4.938,2.24 1.583,0.219 10 Air Fuel Ratio Sensor 3.771,0.979 4.49,1.26 0.719,0.281 10 Heater 3.781,1.458 4.5,1.74 0.719,0.281 10 Sensor 4.979,1.031 5.698,1.313 0.719,0.281 10 HAF2 4.969,1.563 5.688,1.844 0.719,0.281 10 AF2+ 4.99,2.104 5.708,2.385 0.719,0.281 10 AF2- 4.969,2.646 5.688,2.927 0.719,0.281 10 MREL 5.927,1.677 6.729,2.083 0.802,0.406 10 Duty Control 5.677,3.313 6.479,3.719 0.802,0.406 10 ECM


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 4 seconds (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or higher when the heater does not operate for 4 seconds (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0031
·

AFS Voltage B1S1

·

AF Lambda B1S1

·

Exhaust Temperature B1S1


P0032

MONITOR DESCRIPTION

The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0031
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.


P0032 Ignition switch ON for 5 seconds

WIRING DIAGRAM

A284162
3.469,1.667 4.792,2.073 1.323,0.406 10 false Air Fuel Ratio Sensor 4.667,0.417 4.885,0.604 0.219,0.188 10 false 1 1.094,1.823 1.792,2.01 0.698,0.188 10 false EFI NO. 2 1.583,3.688 2.771,3.885 1.188,0.198 10 false EFI-MAIN NO. 2 1.219,5.865 2.292,6.063 1.073,0.198 10 false Battery 1.073,4.667 2.26,4.865 1.188,0.198 10 false EFI-MAIN NO. 2 5.396,0.563 5.854,0.76 0.458,0.198 10 false B76 5.396,1.333 5.854,1.531 0.458,0.198 10 false B76 5.406,2.021 5.865,2.219 0.458,0.198 10 false B76 5.417,3.031 5.875,3.229 0.458,0.198 10 false A61 5.417,0.365 5.875,0.563 0.458,0.198 10 false 104 5.427,1.146 5.885,1.344 0.458,0.198 10 false 125 5.417,1.854 5.875,2.052 0.458,0.198 10 false 126 5.448,2.844 5.906,3.042 0.458,0.198 10 false 45 3.552,0.427 3.771,0.615 0.219,0.188 10 false 2 3.583,1.229 3.802,1.417 0.219,0.188 10 false 4 4.667,1.208 4.885,1.396 0.219,0.188 10 false 3 1.313,3.24 1.531,3.427 0.219,0.188 10 false 1 1.302,4.094 1.521,4.281 0.219,0.188 10 false 2 0.802,3.229 1.021,3.417 0.219,0.188 10 false 3 0.771,4.094 0.99,4.281 0.219,0.188 10 false 5 5.708,0.469 6.323,0.667 0.615,0.198 10 false HAF2 4.219,0.438 4.833,0.635 0.615,0.198 10 false HAF2 5.719,1.219 6.333,1.417 0.615,0.198 10 false AF2+ 5.729,1.885 6.344,2.083 0.615,0.198 10 false AF2- 5.729,3.021 6.344,3.219 0.615,0.198 10 false MREL 3.771,1.198 4.385,1.396 0.615,0.198 10 false AF2- 4.229,1.188 4.844,1.385 0.615,0.198 10 false AF2+ 3.781,0.448 4.396,0.646 0.615,0.198 10 false +B 3.448,1.51 4.063,1.708 0.615,0.198 10 false B8 1.042,5.323 2.229,5.521 1.188,0.198 10 false FL MAIN 6.146,4.854 6.813,5.292 0.667,0.438 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)

NG

13.REPLACE AIR FUEL RATIO SENSOR
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)
a.
A122781
0.552,1 0.99,1.292 0.438,0.292 1.958,1 2.229,0.823 false 0.24,0.125 0.438,0.281 0.198,0.156 10 false *a 2.271,0.698 2.49,0.854 0.219,0.156 10 false +B 0.656,1.073 0.938,1.219 0.281,0.146 10 false B8
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B8-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-1 (HAF2) - B76-104 (HAF2) Always Below 1 Ω
B8-1 (HAF2) or B76-104 (HAF2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B8-2 (+B) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B8-2 (+B) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 2 RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

10.REPLACE EFI-MAIN NO. 2 RELAY
7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

"Exhaust Temperature B1S1" on the GTS screen should be 200°C (392°F) or higher.



i.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0031 and/or P0032.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more again.





Result:
Proceed to
NEXT



NEXT

END

13.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED