Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  


DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger sub-assembly is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger sub-assembly. The nozzle vane opens and closes to change the velocity of exhaust gasses in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance DC motor current is 1.57 A or higher for 5 seconds or more when the motor is operating (1 trip detection logic).
·

Open or short in DC motor circuit

·

DC motor (built into turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored
P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic).
·

Open in DC motor circuit

·

DC motor (built into turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored
P0048 Turbocharger/Supercharger Boost Control "A" Circuit High Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic).
·

Short in DC motor (built into turbocharger sub-assembly) circuit

·

DC motor (built into turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular


Comes on DTC stored

HINT:
·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

·

Vehicle surge when driving with full load


·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

·

Lack of power

·

Vehicle surge or hesitation under light or medium load




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0046 Ignition switch ON for 5 seconds
P0047 2 seconds after engine is started, race engine for 1 second
P0048

WIRING DIAGRAM

A297978
0.198,2.042 2.24,2.427 2.042,0.385 10 false DC motor (Built into Turbocharger sub-assembly) 0.198,1.854 0.51,2.115 0.313,0.26 10 false j1 1.635,0.698 1.948,0.958 0.313,0.26 10 false MB 1.625,1.365 1.938,1.625 0.313,0.26 10 false MA 3.51,1.854 4.281,2.104 0.771,0.25 10 false Shielded 1.958,1.375 2.729,1.625 0.771,0.25 10 false 2 1.948,0.698 2.719,0.948 0.771,0.25 10 false 1 5.24,0.698 6.01,0.948 0.771,0.25 10 false 108 5.24,1.365 6.01,1.615 0.771,0.25 10 false 107 5.573,0.792 6.344,1.042 0.771,0.25 10 false M+ 5.573,1.479 6.344,1.729 0.771,0.25 10 false M- 5.938,2.01 6.708,2.26 0.771,0.25 10 false B76 5.958,2.188 6.729,2.438 0.771,0.25 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0046, P0047 and/or P0048 is output A
DTC P0046, P0047 and/or P0048 and other DTCs are output B


HINT:

If any DTCs other than P0046, P0047 and/or P0048 are output, troubleshoot those DTCs first.




A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

B

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
a.

Inspect the turbocharger sub-assembly (DC motor operation).

Click hereEngine / Hybrid System>1AD-FTV INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
a.
C217215
0.844,1.719 1.406,1.354 false 2.615,1.688 1.948,1.365 false 0.125,0.115 0.302,0.292 0.177,0.177 10 false *a 0.708,1.76 1.021,1.958 0.313,0.198 10 false MA 2.531,1.76 2.844,1.958 0.313,0.198 10 false MB
*a Component without harness connected
(DC Motor)


Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (MA) - 1 (MB) Always 0.3 to 100 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-2 (MA) - B76-107 (M-) Always Below 1 Ω
j1-1 (MB) - B76-108 (M+) Always Below 1 Ω
j1-2 (MA) or B76-107 (M-) - Body ground Always 10 kΩ or higher
j1-1 (MB) or B76-108 (M+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

2 seconds after engine is started, race engine for 1 second.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

8.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED