Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P007C  Charge Air Cooler Temperature Sensor Circuit Low  P007D  Charge Air Cooler Temperature Sensor Circuit High  


DESCRIPTION

A208462
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The intake air temperature sensor (turbo) senses the intake air temperature after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor (turbo) is powered by a 5 V supply from the THIA terminal of the ECM, via resistor R. Resistor R and the intake air temperature sensor (turbo) are connected in series. When the resistance value of the sensor changes in accordance with changes in the intake air temperature, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P007C Intake Air Temp (Turbo)
P007D

HINT:

If DTC P007C or P007D is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P007C Ignition switch ON for 1 second
P007D

WIRING DIAGRAM

A210074
0.542,2.156 2.969,2.323 2.427,0.167 10 Intake Air Temperature Sensor (Turbo) 5.896,2.406 6.292,2.583 0.396,0.177 10 ECM 6.25,0.208 6.479,0.385 0.229,0.177 10 5 V 5.552,0.646 5.906,0.823 0.354,0.177 10 THIA 5.552,1.25 6.01,1.427 0.458,0.177 10 ETHI 6.156,0.521 6.313,0.698 0.156,0.177 10 R 2.448,1.271 2.563,1.458 0.115,0.188 10 1 2.448,0.656 2.563,0.833 0.115,0.177 10 2 5.208,0.646 5.469,0.802 0.26,0.156 10 113 5.26,1.25 5.469,1.427 0.208,0.177 10 90 5.896,2.26 6.198,2.438 0.302,0.177 10 B76 0.542,1.958 0.896,2.135 0.354,0.177 10 A54

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

d.

Read the value.

OK:

Same as air temperature near intake manifold.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as air temperature near intake manifold C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204915
0.521,3.698 0.844,3.917 0.323,0.219 0.583,0.521 0.896,0.677 0.313,0.156 10 *1 2.656,0.469 2.969,0.625 0.313,0.156 10 *2 0.656,3.365 0.969,3.521 0.313,0.156 10 *a 0.563,3.729 0.906,3.927 0.344,0.198 10 A54 2.365,1.344 2.75,1.542 0.385,0.198 10 THIA 2.365,1.823 2.729,2 0.365,0.177 10 ETHI
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

f.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 - B76-113 (THIA) Always Below 1 Ω
A54-1 - B76-90 (ETHI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-2 or B76-113 (THIA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END