Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0100  Mass Air Flow Circuit Malfunction  


DESCRIPTION

The mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.

The internal circuit of the mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 1945 and 8500 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A207644
1.906,1.365 1.677,1.719 false 1.01,2.563 1.375,1.844 false 5.885,1.948 5.573,0.5 5.573,0.5 5.76,0.5 false 6.125,2.094 6.333,3.094 false 5.583,2.531 4.667,3.25 false 2.354,1.948 2.635,1.781 2.635,1.781 2.781,1.781 false 1.708,0.531 1.958,0.688 0.25,0.156 10 +B 1.635,0.875 2.719,1.177 1.083,0.302 10 Power Transistor 2.833,1.698 3.781,1.948 0.948,0.25 10 Output Voltage 1.948,1.25 3.063,1.469 1.115,0.219 10 Hot Wire Element 0.167,2.583 1.365,2.854 1.198,0.271 10 Cold Wire Element 5.802,0.417 6.917,0.635 1.115,0.219 10 Hot Wire Element 5.958,3.125 7.156,3.396 1.198,0.271 10 Cold Wire Element 3.635,3.26 5.75,3.625 2.115,0.365 10 Temperature Sensor (Thermistor) 2.177,2.313 3.375,2.635 1.198,0.323 10 Periodic Signal Conversion Circuit 2.177,3.313 3.344,3.479 1.167,0.167 10 Output Frequency

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass Air Flow Circuit Malfunction Mass air flow meter assembly signal frequency is less than 850 Hz with the engine speed at 400 rpm or higher for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter assembly circuit

·

Mass air flow meter assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0100 MAF

HINT:

If DTC P0100 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

·

Combustion noise increases




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0100 3 seconds after engine is started

WIRING DIAGRAM

A284164
1.542,1.438 2.635,1.781 1.094,0.344 10 false EFI-MAIN NO. 2 0.427,1.729 1.521,2.073 1.094,0.344 10 false EFI-MAIN NO. 2 2.74,0.563 3.521,0.938 0.781,0.375 10 false EFI NO. 1 3.594,2.104 6,2.438 2.406,0.333 10 false Mass Air Flow Meter Assembly 3.656,1.906 3.969,2.104 0.313,0.198 10 false B1 0.667,2.969 1.156,3.354 0.49,0.385 10 false Battery 3.667,0.823 3.875,1.042 0.208,0.219 10 false 3 5.458,0.854 5.729,1.063 0.271,0.208 10 false 65 5.427,1.542 5.833,1.75 0.406,0.208 10 false B76 5.427,2.802 5.833,3.01 0.406,0.208 10 false A61 5.406,1.031 5.813,1.24 0.406,0.208 10 false B76 5.469,1.365 5.74,1.573 0.271,0.208 10 false 64 5.469,2.625 5.74,2.833 0.271,0.208 10 false 45 3.865,0.583 4.177,0.781 0.313,0.198 10 false +B 4.802,0.927 5.115,1.125 0.313,0.198 10 false FG 5.76,0.927 6.073,1.125 0.313,0.198 10 false VG 4.74,1.417 5.135,1.615 0.396,0.198 10 false E2G 5.75,1.417 6.146,1.615 0.396,0.198 10 false EVG 5.76,2.677 6.26,2.906 0.5,0.229 10 false MREL 5.104,1.667 5.313,1.885 0.208,0.219 10 false 2 5.083,1.156 5.292,1.375 0.208,0.219 10 false 1 2.333,0.583 2.542,0.802 0.208,0.219 10 false 3 1.552,0.573 1.76,0.792 0.208,0.219 10 false 5 1.542,1.188 1.75,1.406 0.208,0.219 10 false 2 2.365,1.177 2.573,1.396 0.208,0.219 10 false 1 0.448,2.396 1.542,2.74 1.094,0.344 10 false FL MAIN 6.104,3.323 6.594,3.708 0.49,0.385 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER ASSEMBLY)
a.
A127724
0.26,0.927 0.729,1.188 0.469,0.26 1.792,1.104 2.229,1.771 false 2.302,1.667 2.531,1.865 0.229,0.198 10 +B 0.188,0.167 0.385,0.365 0.198,0.198 10 *a 0.365,0.979 0.583,1.125 0.219,0.146 10 B1
*a Front view of wire harness connector
(to Mass Air Flow Meter Assembly)


Disconnect the mass air flow meter assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B1-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - EFI-MAIN NO. 2 RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-1 (FG) - B76-65 (VG) Always Below 1 Ω
B1-2 (E2G) - B76-64 (EVG) Always Below 1 Ω
B1-1 (FG) or B76-65 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER ASSEMBLY

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE MASS AIR FLOW METER ASSEMBLY
a.

Replace the mass air flow meter assembly.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

After engine is started for 3 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Proceed to
DTC P0100 is output
DTC is not output




DTC P0100 is output

5.REPLACE ECM

DTC is not output

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER ASSEMBLY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the mass air flow meter assembly connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B1-3 (+B) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B1-3 (+B) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT EFI-MAIN NO. 2 RELAY

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

11.REPLACE EFI-MAIN NO. 2 RELAY
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine and wait for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END