Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor.

The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:

If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0115 Engine Coolant Temperature Circuit Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0117 Engine Coolant Temperature Circuit Low Input Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored
P0118 Engine Coolant Temperature Circuit High Input Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0115 Coolant Temp
P0117
P0118

HINT:
·

If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Reference:
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0115 Ignition switch ON for 0.5 seconds
P0117
P0118

WIRING DIAGRAM

A210074
0.344,2.146 2.656,2.313 2.313,0.167 10 false Engine Coolant Temperature Sensor 5.938,2.448 6.333,2.625 0.396,0.177 10 false ECM 6.24,0.208 6.469,0.385 0.229,0.177 10 false 5 V 5.531,1.5 6.167,1.719 0.635,0.219 10 false ETHW 6.156,0.521 6.313,0.698 0.156,0.177 10 false R 2.448,1.25 2.563,1.438 0.115,0.188 10 false 1 2.448,0.635 2.563,0.813 0.115,0.177 10 false 2 5.198,0.646 5.458,0.802 0.26,0.156 10 false 111 5.25,1.25 5.458,1.427 0.208,0.177 10 false 88 0.354,1.969 0.563,2.125 0.208,0.156 10 false B4 5.938,2.271 6.229,2.417 0.292,0.146 10 false B76 5.542,0.625 5.896,0.802 0.354,0.177 10 false THW

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

d.

Read the value.

OK:

60 to 90°C (140 to 194°F) with warm engine.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) B
60 to 90°C (140 to 194°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A213406
0.531,3.427 0.948,3.75 0.417,0.323 0.708,0.531 1.021,0.688 0.313,0.156 10 false *1 2.531,0.469 2.844,0.625 0.313,0.156 10 false *2 0.229,2.833 0.542,2.99 0.313,0.156 10 false *a 0.635,3.51 0.948,3.708 0.313,0.198 10 false B4 2.427,1.25 2.885,1.448 0.458,0.198 10 false THW 2.417,1.729 2.875,1.927 0.458,0.198 10 false ETHW
*1 Engine coolant temperature sensor
*2 ECM
*a Front view of wire harness connector
(to Engine coolant temperature sensor)


Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

f.

Read the value.

Standard value:

140°C (284°F)



Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B4-2 - B76-111 (THW) Always Below 1 Ω
B4-1 - B76-88 (ETHW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A226261C04
0.917,1.771 1.281,2.0 0.365,0.229 10 *1 2.667,1.771 3.031,2.0 0.365,0.229 10 *2 2.0,0.667 2.458,0.938 0.458,0.271 10 THW 1.917,1.01 2.438,1.25 0.521,0.24 10 ETHW
*1 Engine Coolant Temperature Sensor
*2 ECM


Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

9.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B4-2 or B76-111 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON for 1 second.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END