Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

A208462
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The fuel temperature sensor is built into the supply pump assembly and senses the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes in voltage (See Fig. 1).

The fuel temperature sensor is powered by a 5 V supply from the THF terminal of the ECM, via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the supply pump assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0180 Fuel Temperature Sensor "A" Circuit Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into supply pump assembly)

·

ECM


Comes on DTC stored
P0182 Fuel Temperature Sensor "A" Circuit Low Input Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor (built into supply pump assembly)

·

ECM


Comes on DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Input Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor (built into supply pump assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0180 Fuel Temperature
P0182
P0183

HINT:

If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0180 Ignition switch ON for 0.5 seconds
P0182
P0183

WIRING DIAGRAM

A210074
0.635,2.135 2.281,2.302 1.646,0.167 10 false Fuel Temperature Sensor 5.958,2.427 6.354,2.604 0.396,0.177 10 false ECM 6.25,0.208 6.479,0.385 0.229,0.177 10 false 5 V 5.542,0.625 5.896,0.802 0.354,0.177 10 false THF 6.167,0.531 6.323,0.708 0.156,0.177 10 false R 2.448,1.281 2.563,1.469 0.115,0.188 10 false 1 2.448,0.667 2.563,0.844 0.115,0.177 10 false 2 5.208,0.646 5.458,0.802 0.25,0.156 10 false 112 5.26,1.26 5.469,1.438 0.208,0.177 10 false 89 0.635,1.948 0.917,2.135 0.281,0.188 10 false B49 5.958,2.26 6.25,2.406 0.292,0.146 10 false B76 5.552,1.25 6.01,1.427 0.458,0.177 10 false ETHF

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing the supply pump assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (FUEL TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

d.

Read the value.

OK:

Same value as the actual fuel temperature.


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual fuel temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

10.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204471
0.563,3.375 0.979,3.677 0.417,0.302 0.708,0.375 1.021,0.531 0.313,0.156 10 false *1 2.552,0.25 2.865,0.406 0.313,0.156 10 false *2 0.49,2.865 0.802,3.021 0.313,0.156 10 false *a 0.646,3.438 1.104,3.635 0.458,0.198 10 false B49 2.385,1.031 2.844,1.229 0.458,0.198 10 false THF 2.375,1.583 2.833,1.781 0.458,0.198 10 false ETHF
*1 Fuel Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Fuel Temperature Sensor)


Disconnect the fuel temperature sensor connector.


b.

Connect terminals 2 and 1 of the fuel temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

f.

Read the value.

OK:

140°C (284°F) or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE FUEL TEMPERATURE SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
3.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.BLEED AIR FROM FUEL SYSTEM
4.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

5.PERFORM SUPPLY PUMP INITIALIZATION
5.PERFORM SUPPLY PUMP INITIALIZATION
a.

Perform the supply pump initialization.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B49-2 - B76-112 (THF) Always Below 1 Ω
B49-1 - B76-89 (ETHF) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch to ON for 1 second or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

10.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A226261
0.917,1.771 1.281,2 0.365,0.229 10 *1 2.667,1.771 3.031,2 0.365,0.229 10 *2 2.021,0.667 2.479,0.938 0.458,0.271 10 THF 1.938,1.01 2.458,1.25 0.521,0.24 10 ETHF
*1 Fuel Temperature Sensor
*2 ECM


Disconnect the fuel temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Temperature.

Powertrain > Engine > Data List
Tester Display
Fuel Temperature
50003 61 403

e.

Read the value.

OK:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

11.REPLACE FUEL TEMPERATURE SENSOR (FUEL TEMPERATURE SENSOR)

NG

12.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
11.REPLACE FUEL TEMPERATURE SENSOR (FUEL TEMPERATURE SENSOR)
a.

Replace the fuel temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.BLEED AIR FROM FUEL SYSTEM
12.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B49-2 or B76-112 (THF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED