Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0191  Fuel Rail Pressure Sensor Circuit Range / Performance  


DESCRIPTION

Refer to DTC P0087.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0087

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0191 Fuel Rail Pressure Sensor Circuit Range / Performance The difference between the main and sub voltage outputs of the fuel pressure sensor is 0.04 V or less, or 1.06 V or higher for 1 second or more (1 trip detection logic).
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (built into common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0191
·

Fuel Press

·

Target Common Rail Pressure



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0191 Idling for 1 second

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
50003 61 706,54

d.

Start the engine.


e.

Check the change in the values for the Data List items above when increasing the engine speed from idling to 3000 rpm with no load.

Result:
Result Proceed to
Fuel Press is always 10000 kPa or less
or
Fuel Press is always 200000 kPa or higher
A
Except above B


HINT:

When in a stable condition such as when idling after warm up the engine, "Fuel Press" is +/-5000 kPa of "Target Common Rail Pressure".




A

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B70-5 (PR) - B76-66 (PCR1) Always Below 1 Ω
B70-2 (PR2) - B76-114 (PCR2) Always Below 1 Ω
B70-1 (VCS) - B76-69 (VCS) Always Below 1 Ω
B70-6 (VC) - B76-68 (VCM) Always Below 1 Ω
B70-4 (E2) - B76-67 (E2M) Always Below 1 Ω
B70-3 (E2S) - B76-91 (E2S) Always Below 1 Ω
B70-5 (PR) or B76-66 (PCR1) - Body ground Always 10 kΩ or higher
B70-2 (PR2) or B76-114 (PCR2) - Body ground Always 10 kΩ or higher
B70-1 (VCS) or B76-69 (VCS) - Body ground Always 10 kΩ or higher
B70-6 (VC) or B76-68 (VCM) - Body ground Always 10 kΩ or higher
B70-4 (E2) or B76-67 (E2M) - Body ground Always 10 kΩ or higher
B70-3 (E2S) or B76-91 (E2S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE COMMON RAIL ASSEMBLY

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0191 is output A
DTC is not output B




A

5.REPLACE COMMON RAIL ASSEMBLY

B

END

5.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1AD-FTV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0191 is output A
DTC is not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END