Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0524  Engine Oil Pressure Too Low  


DESCRIPTION

The oil pressure control system reduces and increases engine oil pressure using the oil pressure switching valve assembly in the oil filter bracket. When the engine speed reaches 2200 rpm while racing the engine after warming it up, the oil pressure switching valve assembly operates and the engine oil pressure system changes from low pressure control mode to high pressure control mode. When the engine speed drops to 2100 rpm, the engine oil pressure system changes from high pressure control mode to low pressure control mode. The oil pressure sender gauge assembly detects the engine oil pressure.

A250712
3.365,2.313 3.604,2.542 false 5.229,0.729 5.531,1.031 false 3.688,2.448 4.979,2.635 1.292,0.188 10 Low Oil Pressure 5.594,0.958 6.885,1.146 1.292,0.188 10 High Oil Pressure 0.51,1.125 1.188,1.833 0.677,0.708 10 Engine Oil Pressure 3.271,3.167 4.229,3.542 0.958,0.375 10 Engine Speed

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0524 Engine Oil Pressure Too Low Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):
(a) 0.3 seconds have elapsed after sending a command to change from low oil pressure control mode to high oil pressure control mode.
(b) The oil pressure control system does not change to high oil pressure control mode.
·

Short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

Oil pressure switching valve assembly

·

ECM

·

Oil pump assembly

·

Engine oil amount insufficient


Comes on DTC stored

HINT:

Checking the state of the oil level warning light and oil pressure warning light will help in understanding why this DTC was stored.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION


Related Data List
DTC No. Data List
P0524 Engine Oil Pressure
Eng Oil Press Switch Valve

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0524 After warming up the engine, race the engine at 2200 rpm or higher.*

*: Using the GTS, the oil pressure control system can be inspected by performing Engine Oil Pressure Control Check. Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

An output DTC does not necessarily indicate that there is a malfunction. DTCs may have been stored due to an insufficient engine oil amount even though the oil level warning light is currently not illuminated, such as when engine oil is added by the customer.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0524)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0524 is output A
DTC P0524 and other DTCs are output B


HINT:

If any DTCs other than P0524 are output, troubleshoot those DTCs first.




A

2.CHECK ENGINE OIL LEVEL

B

2.CHECK ENGINE OIL LEVEL

b.

Check the state of the oil level warning light.

Result:
Result Proceed to
Engine oil level is low and oil level warning light is illuminated A
Engine oil level is within the specified range and oil level warning light is not illuminated B


HINT:

If the oil level warning light is not illuminated even though the engine oil level is lower than the Low mark, or the oil level warning light is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts for malfunctions.




A

3.CHECK ENGINE OIL LEAKS

B

5.PERFORM ENGINE OIL PRESSURE CONTROL SYSTEM CHECK
3.CHECK ENGINE OIL LEAKS
a.

Check for engine oil leaks.

Result:

If there are engine oil leaks, perform repairs.



Result:
Proceed to
NEXT



NEXT

4.ADD ENGINE OIL
4.ADD ENGINE OIL
a.

Add engine oil.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ENGINE OIL PRESSURE CONTROL SYSTEM CHECK
5.PERFORM ENGINE OIL PRESSURE CONTROL SYSTEM CHECK
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION

Powertrain > Engine > Utility
Tester Display
Engine Oil Pressure Control Check
50005 61 4173

e.

Compare the "Valve OFF: Hi Oil press" (high pressure control mode) and "Valve ON: Low Oil press" (low pressure control mode) oil pressure values and check the difference.

Standard:

50 kPa or higher.



Result:
Proceed to
OK
NG



OK

END

NG

6.INSPECT ENGINE OIL PRESSURE
6.INSPECT ENGINE OIL PRESSURE

Result:
Proceed to
OK
NG



OK

7.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

8.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
7.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE OIL PRESSURE SWITCHING VALVE ASSEMBLY
a.

Replace the oil pressure switching valve assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PRESSURE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM ENGINE OIL PRESSURE CONTROL SYSTEM CHECK
9.PERFORM ENGINE OIL PRESSURE CONTROL SYSTEM CHECK
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION

Powertrain > Engine > Utility
Tester Display
Engine Oil Pressure Control Check
50005 61 4173

e.

Compare the "Valve OFF: High Oil press" (high pressure control mode) and "Valve ON: Low Oil press" (low pressure control mode) oil pressure values and check the difference.

Standard:

50 kPa or higher.



Result:
Proceed to
OK
NG



OK

END

NG

10.REPAIR OR REPLACE OIL PUMP ASSEMBLY
10.REPAIR OR REPLACE OIL PUMP ASSEMBLY
a.

Repair or replace the oil pump assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PUMP>REMOVAL

HINT:

If the oil pressure does not rise after disconnecting the connector of the oil pressure switching valve assembly, or if the oil pressure changes, but the difference between the low oil pressure and high oil pressure is small, a mechanical malfunction is probably the cause.

·

The sleeve is locked due to foreign matter.

·

The oil pressure relief valve is locked due to foreign matter

·

The check valve is stuck.




Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Utility / Engine Oil Pressure Control Check.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION

Powertrain > Engine > Utility
Tester Display
Engine Oil Pressure Control Check
50005 61 4173

e.

Compare the "Valve OFF: Hi Oil press" (high pressure control mode) and "Valve ON: Low Oil press" (low pressure control mode) oil pressure values and check that the oil pressure has risen.


Result:
Proceed to
NEXT



NEXT

END