Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0522  Engine Oil Pressure Sensor / Switch Low  P0523  Engine Oil Pressure Sensor / Switch High  


DESCRIPTION

Refer to DTC P0524.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0524

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0522 Engine Oil Pressure Sensor / Switch Low Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Oil pressure sender gauge assembly voltage is 0.05 V or less.
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Does not come on DTC stored
P0523 Engine Oil Pressure Sensor / Switch High Conditions (a) and (b) continue for 5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Oil pressure sender gauge assembly voltage is 4.6 V or higher.
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0522
P0523
Engine Oil Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0522 Idling for 5 second
P0523

WIRING DIAGRAM

A298536
1.083,1.51 3.573,1.771 2.49,0.26 10 false Oil Pressure Sender Gauge Assembly 4.24,3 5.646,3.438 1.406,0.438 10 false Oil Pressure Switching Valve Assembly 4.24,2.823 4.688,3.021 0.448,0.198 10 false B65 1.094,1.333 1.542,1.531 0.448,0.198 10 false B66 2.469,0.406 2.917,0.604 0.448,0.198 10 false VC 2.302,0.823 2.75,1.021 0.448,0.198 10 false VOUT 2.375,1.229 2.823,1.427 0.448,0.198 10 false GND 2.792,0.26 3.24,0.458 0.448,0.198 10 false 3 2.792,0.719 3.24,0.917 0.448,0.198 10 false 2 2.792,1.104 3.24,1.302 0.448,0.198 10 false 1 5.646,0.188 6.094,0.385 0.448,0.198 10 false 93 5.594,0.396 6.042,0.594 0.448,0.198 10 false B76 5.594,0.823 6.042,1.021 0.448,0.198 10 false B76 5.604,1.219 6.052,1.417 0.448,0.198 10 false B76 5.615,0.615 6.063,0.813 0.448,0.198 10 false 116 5.646,1.031 6.094,1.229 0.448,0.198 10 false 70 5.635,3.813 6.083,4.01 0.448,0.198 10 false 83 5.604,4.021 6.052,4.219 0.448,0.198 10 false B76 5.604,4.698 6.052,4.896 0.448,0.198 10 false A61 5.656,4.49 6.104,4.688 0.448,0.198 10 false 45 6.208,5.26 6.656,5.458 0.448,0.198 10 false ECM 5.99,4.719 6.552,4.938 0.563,0.219 10 false MREL 5.979,1.219 6.542,1.438 0.563,0.219 10 false EPOP 5.979,0.844 6.542,1.063 0.563,0.219 10 false POP 5.979,0.406 6.542,0.625 0.563,0.219 10 false VPOP 5.99,4.031 6.552,4.25 0.563,0.219 10 false EOPV 3.792,2.771 4.354,2.99 0.563,0.219 10 false 2 3.792,3.604 4.24,3.802 0.448,0.198 10 false 1 2.906,2.5 3.885,2.75 0.979,0.25 10 false EFI NO .1 2.427,2.198 2.875,2.396 0.448,0.198 10 false 3 1.615,2.729 2.063,2.927 0.448,0.198 10 false 1 1.625,2.188 2.073,2.385 0.448,0.198 10 false 5 2.417,2.729 2.865,2.927 0.448,0.198 10 false 2 1.573,3.021 2.667,3.208 1.094,0.188 10 false EFI-MAIN NO. 2 0.625,2.458 1.802,2.688 1.177,0.229 10 false EFI-MAIN NO. 2 0.625,3.5 1.438,3.75 0.813,0.25 10 false FL MAIN 0.792,5 1.604,5.25 0.813,0.25 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
a.

Disconnect the oil pressure sender gauge assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B66-3 (VC) - B76-93 (VPOP) Always Below 1 Ω
B66-2 (VOUT) - B76-116 (POP) Always Below 1 Ω
B66-1 (GND) - B76-70 (EPOP) Always Below 1 Ω
B66-3 (VC) or B76-93 (VPOP) - Body ground Always 10 kΩ or higher
B66-2 (VOUT) or B76-116 (POP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)
a.
A241069
0.448,1.073 0.865,1.333 0.417,0.26 1.833,1.333 2.031,1.656 true 0.094,0.083 0.323,0.313 0.229,0.229 10 false *a 2.01,1.708 2.302,1.885 0.292,0.177 10 false VC 0.51,1.115 1.177,1.438 0.667,0.323 10 false B66
*a Front view of wire harness connector
(to Oil Pressure Sender Gauge Assembly)


Disconnect the oil pressure sender gauge assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Condition Specified Condition
B66-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1AD-FTV LUBRICATION>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0522 OR P0523)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0522 OR P0523)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 5 second or more.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0522 or P0523 is output A
DTC is not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine and idle it for 5 second or more.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END