Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
·

Open in back up power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0560 Battery Voltage*

*: This is not the voltage of the BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0560 Ignition switch ON for 3 seconds

WIRING DIAGRAM

A284166
3.531,2.771 4.563,3.042 1.031,0.271 10 false EFI-MAIN NO. 1 1.792,2.219 2.823,2.49 1.031,0.271 10 false EFI-MAIN NO. 1 3.615,1.167 4.302,1.438 0.688,0.271 10 false EFI NO. 3 0.792,2.844 1.375,3.146 0.583,0.302 10 false Battery 5.531,2.573 5.948,2.833 0.417,0.26 10 false MREL 6.01,3.354 6.51,3.615 0.5,0.26 10 false A61 6.01,3.521 6.552,3.708 0.542,0.188 10 false ECM 5.552,2.083 5.969,2.344 0.417,0.26 10 false +B 5.542,1.75 5.958,2.01 0.417,0.26 10 false +B2 5.521,1.01 5.938,1.271 0.417,0.26 10 false BATT 5.271,2.313 5.552,2.573 0.281,0.26 10 false 45 5.292,1.958 5.573,2.219 0.281,0.26 10 false 1 5.24,1.635 5.521,1.896 0.281,0.26 10 false 20 5.302,0.906 5.583,1.167 0.281,0.26 10 false 2 4.281,2.521 4.563,2.781 0.281,0.26 10 false 1 3.49,2.531 3.771,2.792 0.281,0.26 10 false 2 4.302,1.958 4.583,2.219 0.281,0.26 10 false 3 3.49,1.938 3.771,2.198 0.281,0.26 10 false 5 0.719,2.26 1.75,2.531 1.031,0.271 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When the ignition switch is turned to ON, even though +B voltage is present, when the voltage at terminal BATT (power supply for maintaining memorized values in the ECM) drops excessively, this DTC is stored.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BATT VOLTAGE)
a.
A204368
0.25,1.135 0.646,1.375 0.396,0.24 1.635,0.865 1.281,1.875 true 0.25,0.167 0.427,0.344 0.177,0.177 10 false *a 1.094,1.906 1.875,2.104 0.781,0.198 10 false 2 (BATT) 0.292,1.167 0.677,1.385 0.385,0.219 10 false A61
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A61-2 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

8.RECHARGE OR REPLACE BATTERY
3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.REPAIR OR REPLACE BATTERY TERMINAL
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON for 3 seconds.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0560 is output A
DTC is not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

8.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED