Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2013.11
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

ST NO. 1 relay circuit

·

Clutch start switch assembly

·

Ignition or starter switch assembly*

·

ECM


Comes on DTC stored

*: w/o entry and start system


Related Data List
DTC No. Data List
P0617 Starter Signal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0617 Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or higher

WIRING DIAGRAM

A294528
0.104,0.104 2.052,0.313 1.948,0.208 12 false w/ Entry and Start System: 1.479,0.854 1.719,1.031 0.24,0.177 10 false NE 1.313,1.396 1.719,1.583 0.406,0.188 10 false STAR 1.406,1.917 1.719,2.094 0.313,0.177 10 false STA 1.792,0.75 2.031,0.927 0.24,0.177 10 false 16 1.802,1.292 2.042,1.469 0.24,0.177 10 false 5 1.802,1.813 2.042,1.99 0.24,0.177 10 false 7 0.167,2.281 0.448,2.448 0.281,0.167 10 false G82 0.167,2.448 1.969,2.792 1.802,0.344 10 false Certification ECU (Smart Key ECU Assembly) 3.698,2.385 4.281,2.625 0.583,0.24 10 false A4*1 3.667,2.833 4.865,3.167 1.198,0.333 10 false Clutch Start Switch Assembly 3.458,2.438 3.615,2.615 0.156,0.177 10 false 2 3.458,3.365 3.615,3.542 0.156,0.177 10 false 1 5.448,0.75 5.688,0.927 0.24,0.177 10 false 10 5.448,1.281 5.688,1.458 0.24,0.177 10 false 28 5.458,1.771 5.698,1.948 0.24,0.177 10 false 21 5.729,0.844 6.052,1.031 0.323,0.188 10 false NE 5.729,1.396 6.031,1.573 0.302,0.177 10 false CLL 5.729,1.875 6.063,2.052 0.333,0.177 10 false STA 5.427,2.333 5.896,2.521 0.469,0.188 10 false A66 5.417,2.5 7.104,2.854 1.688,0.354 10 false Engine Stop and Start ECU 5.469,3.667 5.708,3.844 0.24,0.177 10 false 10 5.458,4.469 5.698,4.646 0.24,0.177 10 false 43 5.719,3.771 6.052,3.948 0.333,0.177 10 false NEO 5.719,4.469 6.063,4.646 0.344,0.177 10 false STA 5.875,5.365 6.25,5.531 0.375,0.167 10 false A61 6.271,5.365 6.625,5.542 0.354,0.177 10 false ECM 3.031,4.667 3.188,4.844 0.156,0.177 10 false 2 3.021,5.573 3.177,5.75 0.156,0.177 10 false 1 3.302,5.083 3.927,5.26 0.625,0.177 10 false ST 2.542,4.656 2.698,4.833 0.156,0.177 10 false 5 2.552,5.573 2.708,5.75 0.156,0.177 10 false 3 0.615,5.125 1.24,5.302 0.625,0.177 10 false FL MAIN 0.604,3.583 0.844,3.76 0.24,0.177 10 false ST 0.76,6.573 1.26,6.75 0.5,0.177 10 false Battery 1.115,5.927 1.271,6.104 0.156,0.177 10 false 1 1.563,5.896 1.719,6.073 0.156,0.177 10 false 1 1.792,5.906 2.01,6.073 0.219,0.167 10 false B6 1.083,6.125 1.281,6.302 0.198,0.177 10 false C4 1.344,6.927 1.99,7.281 0.646,0.354 10 false Starter Assembly 3.698,2.594 4.281,2.833 0.583,0.24 10 false F2*2 3.906,5.969 4.531,6.146 0.625,0.177 10 false *1: LHD 3.917,6.198 4.542,6.375 0.625,0.177 10 false *2: RHD

A294529
0.104,0.104 2.146,0.313 2.042,0.208 12 false w/o Entry and Start System: 1.115,1.729 1.333,1.906 0.219,0.177 10 false G4 1.115,1.885 2.625,2.229 1.51,0.344 10 false Ignition or Starter Switch Assembly 0.583,2.177 0.906,2.344 0.323,0.167 10 false AM2 1.49,3.229 1.708,3.406 0.219,0.177 10 false ST 3.458,2.438 3.594,2.615 0.135,0.177 10 false 2 3.448,3.333 3.583,3.51 0.135,0.177 10 false 1 3.656,2.375 4.208,2.635 0.552,0.26 10 false A4*1 3.667,2.823 4.865,3.177 1.198,0.354 10 false Clutch Start Switch Assembly 0.615,5.094 1.208,5.26 0.594,0.167 10 false FL MAIN 3.042,4.667 3.177,4.844 0.135,0.177 10 false 2 3.042,5.583 3.177,5.76 0.135,0.177 10 false 1 3.302,5.083 3.906,5.24 0.604,0.156 10 false ST 0.75,6.594 1.229,6.771 0.479,0.177 10 false Battery 1.094,6.125 1.313,6.302 0.219,0.177 10 false C4 1.792,5.906 2.01,6.083 0.219,0.177 10 false B6 2.531,4.656 2.667,4.833 0.135,0.177 10 false 5 2.531,5.573 2.667,5.75 0.135,0.177 10 false 3 1.115,5.927 1.25,6.104 0.135,0.177 10 false 1 1.552,5.906 1.688,6.083 0.135,0.177 10 false 1 1.323,6.927 1.958,7.281 0.635,0.354 10 false Starter Assembly 5.896,5.365 6.25,5.531 0.354,0.167 10 false A61 6.292,5.365 6.635,5.542 0.344,0.177 10 false ECM 5.729,4.469 6.063,4.646 0.333,0.177 10 false STA 5.729,1.906 6.052,2.083 0.323,0.177 10 false STA 5.729,3.75 6.083,3.927 0.354,0.177 10 false NEO 5.729,0.844 6.073,1.021 0.344,0.177 10 false NE 5.729,1.396 6.031,1.573 0.302,0.177 10 false CLL 5.448,0.75 5.667,0.927 0.219,0.177 10 false 10 5.448,1.281 5.667,1.458 0.219,0.177 10 false 28 5.448,1.771 5.667,1.948 0.219,0.177 10 false 21 1.208,1.281 1.344,1.458 0.135,0.177 10 false 4 2.333,1.281 2.469,1.458 0.135,0.177 10 false 2 1.406,1.281 1.75,1.458 0.344,0.177 10 false AM2 1.979,1.281 2.26,1.458 0.281,0.177 10 false ST2 5.417,2.333 5.865,2.51 0.448,0.177 10 false A66 5.417,2.5 7.115,2.823 1.698,0.323 10 false Engine Stop and Start ECU 5.448,3.667 5.667,3.844 0.219,0.177 10 false 10 5.448,4.469 5.667,4.646 0.219,0.177 10 false 43 3.656,2.594 4.208,2.854 0.552,0.26 10 false F2*2 3.927,6 4.521,6.167 0.594,0.167 10 false *1: LHD 3.938,6.219 4.531,6.385 0.594,0.167 10 false *2: RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON (w/ entry and start system) B
ON (w/o entry and start system) C




A

B

2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

C

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
2.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - engine stop and start ECU - certification ECU (smart key ECU assembly) - ST NO. 1 relay).


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER DTC OUTPUT RECURS
3.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0617 is output A
DTC is not output B




A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
5.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (ECM - clutch start switch assembly - engine stop and start ECU - ST relay).


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS
8.REPLACE IGNITION OR STARTER SWITCH ASSEMBLY
a.

Replace the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1AD-FTV STARTING>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER DTC OUTPUT RECURS