Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P245C  EGR Cooler Bypass Control Circuit Low  P245D  EGR Cooler Bypass Control Circuit High  


DESCRIPTION

The No.1 vacuum switching valve assembly (for EGR cooler) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245C EGR Cooler Bypass Control Circuit Low Open or short in the No.1 vacuum switching valve assembly (for EGR cooler) for 3 seconds (1 trip detection logic).
·

Open or short in No.1 vacuum switching valve assembly (for EGR cooler) circuit

·

No.1 vacuum switching valve assembly (for EGR cooler)

·

ECM


Comes on DTC stored
P245D EGR Cooler Bypass Control Circuit High Open or short in the No.1 vacuum switching valve assembly (for EGR cooler) for 3 seconds (1 trip detection logic).
·

Open or short in No.1 vacuum switching valve assembly (for EGR cooler) circuit

·

No.1 vacuum switching valve assembly (for EGR cooler)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P245C Ignition switch ON for 3 seconds
P245D

WIRING DIAGRAM

A284163
5.75,1.031 6.448,1.333 0.698,0.302 10 false ECBV 1.281,0.906 1.552,1.125 0.271,0.219 10 false 5 0.594,2.365 1.813,2.563 1.219,0.198 10 false EFI-MAIN NO. 2 1.219,1.719 2.438,1.917 1.219,0.198 10 false EFI-MAIN NO. 2 5.406,1.031 5.771,1.25 0.365,0.219 10 false B76 5.417,2.146 5.781,2.365 0.365,0.219 10 false A61 5.448,0.844 5.813,1.063 0.365,0.219 10 false 106 5.458,1.969 5.823,2.188 0.365,0.219 10 false 45 5.719,2.063 6.417,2.365 0.698,0.302 10 false MREL 2.604,0.844 3.385,1.031 0.781,0.188 10 false EFI NO. 1 1.281,1.417 1.552,1.635 0.271,0.219 10 false 2 2.115,1.417 2.385,1.635 0.271,0.219 10 false 1 2.125,0.927 2.396,1.146 0.271,0.219 10 false 3 4.719,0.896 4.99,1.115 0.271,0.219 10 false 2 3.719,0.896 3.99,1.115 0.271,0.219 10 false 1 3.531,1.365 5.177,2.115 1.646,0.75 10 false NO. 1 Vacuum Switching Valve (for EGR cooler) 3.49,1.156 3.802,1.344 0.313,0.188 10 false B56 0.573,3.031 1.792,3.229 1.219,0.198 10 false FL MAIN 6.135,3.896 6.833,4.198 0.698,0.302 10 false ECM 0.729,3.719 1.948,3.917 1.219,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR COOLER)
a.

Inspect the No. 1 vacuum switching valve assembly (for EGR cooler).

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER))

NG

12.REPLACE NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR COOLER)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER))
a.
A204918
0.292,0.958 0.75,1.26 0.458,0.302 0.281,0.083 0.5,0.26 0.219,0.177 10 *a 0.375,1.01 0.646,1.177 0.271,0.167 10 B56
*a Front view of wire harness connector
(to No. 1 Vacuum Switching Valve (for EGR cooler))


Disconnect the No. 1 vacuum switching valve (for EGR cooler) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B56-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER) - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER) - ECM)
a.

Disconnect the No. 1 vacuum switching valve (for EGR cooler) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B56-2 - B76-106 (ECBV) Always Below 1 Ω
B56-2 or B76-106 (ECBV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR EGR COOLER) - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the NO.1 vacuum switching valve (for EGR cooler) connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B56-1 - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B56-1 or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 2 RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

10.REPLACE EFI-MAIN NO. 2 RELAY
7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Result
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE NO.1 VACUUM SWITCHING VALVE ASSEMBLY (FOR EGR COOLER)
a.

Replace the No. 1 vacuum switching valve assembly (for EGR cooler).

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END