Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A298704
1.177,2.219 0.771,1.24 0.771,1.24 1.01,1.24 true 1.313,1.729 1.604,1.25 1.604,1.25 1.75,1.25 true 1.281,2.948 1.385,3.417 1.385,3.417 1.531,3.417 true 1.052,1.177 2.125,1.375 1.073,0.198 10 Hall IC 1.802,1.177 2.875,1.375 1.073,0.198 10 Magnet 1.573,3.354 2.646,3.552 1.073,0.198 10 Magnet 0.063,2.583 0.531,2.948 0.469,0.365 10 Sensor Vane 0.375,3.75 2.542,4.354 2.167,0.604 10 Nozzle Vane Position Sensor (Built into Turbocharger Sub-assembly) 2.365,1.323 3.438,1.521 1.073,0.198 10 VC 2.365,2.115 3.438,2.313 1.073,0.198 10 VTA 2.375,2.885 3.448,3.083 1.073,0.198 10 E2 3.021,1.438 4.094,1.635 1.073,0.198 10 VNVC 3.01,2.24 4.083,2.438 1.073,0.198 10 VNA 3.021,3.021 4.094,3.219 1.073,0.198 10 VNE2 3.104,3.406 4.177,3.604 1.073,0.198 10 ECM 4.094,1.542 5.167,1.74 1.073,0.198 10 4.65 4.094,2.417 5.167,2.615 1.073,0.198 10 0.35 4.771,3.24 5.844,3.438 1.073,0.198 10 Closed 5.833,3.24 6.906,3.438 1.073,0.198 10 Open 5.573,3.542 7.021,3.74 1.448,0.198 10 Nozzle Vane Position 3.708,0.563 5.531,1.063 1.823,0.5 10 Nozzle Vane Position Sensor Output Voltage (V)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (built into turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored
P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (built into turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM


Comes on DTC stored

HINT:

If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

·

Lack of power

·

Vehicle surge or hesitation under light or medium load




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2564 Ignition switch ON for 1 second
P2565

WIRING DIAGRAM

A298703
0.167,2.271 2.594,2.656 2.427,0.385 10 false Nozzle Vane Position Sensor (Built into Turbocharger Sub-assembly) 0.167,2.104 0.479,2.302 0.313,0.198 10 false j2 1.74,0.688 2.052,0.885 0.313,0.198 10 false VC 1.688,1.167 2,1.365 0.313,0.198 10 false VTA 1.76,1.615 2.073,1.813 0.313,0.198 10 false E2 2.063,0.594 2.375,0.792 0.313,0.198 10 false 1 2.073,1.052 2.385,1.25 0.313,0.198 10 false 3 2.083,1.5 2.396,1.698 0.313,0.198 10 false 2 5.01,0.583 5.323,0.781 0.313,0.198 10 false 101 5.021,1.063 5.333,1.26 0.313,0.198 10 false 124 5.031,1.531 5.344,1.729 0.313,0.198 10 false 100 5.323,0.583 5.917,0.781 0.594,0.198 10 false VNVC 5.333,1.073 5.927,1.271 0.594,0.198 10 false VNA 5.333,1.531 5.927,1.729 0.594,0.198 10 false VNE2 5.531,2.292 6.125,2.49 0.594,0.198 10 false B76 5.979,2.292 6.573,2.49 0.594,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 OR P2565)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P2564 or P2565 is output A
DTC P2564 or P2565 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)

B

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - ECM)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j2-3 (VTA) - B76-124 (VNA) Always Below 1 Ω
j2-2 (E2) - B76-100 (VNE2) Always Below 1 Ω
j2-1 (VC) - B76-101 (VNVC) Always Below 1 Ω
j2-3 (VTA) or B76-124 (VNA) - Body ground Always 10 kΩ or higher
j2-1 (VC) or B76-101 (VNVC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NOZZLE VANE POSITION SENSOR)
a.
C129053
0.635,1 0.99,1.25 0.354,0.25 1.49,1.24 1.292,1.552 true 1.771,1.24 1.906,1.552 true 0.74,1.052 1.021,1.229 0.281,0.177 10 false j2 1.146,1.573 1.396,1.729 0.25,0.156 10 false VC 0.094,0.063 0.313,0.219 0.219,0.156 10 false *a 1.833,1.583 2.063,1.74 0.229,0.156 10 false E2
*a Front view of wire harness connector
(to Nozzle Vane Position Sensor)


Disconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j2-1 (VC) - j2-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NG

5.REPLACE ECM
4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and leave the vehicle for 15 seconds.


f.

Turn the ignition switch to ON for 1 second.


g.

Turn the GTS on.


h.

Confirm that the DTC is not output.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P2564 and/or P2565.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.



Result:
Proceed to
NEXT



NEXT

END