This DTC indicates that the vacuum regulating valve assembly of the turbocharger is malfunctioning. The ECM monitors the vacuum regulating valve assembly current to detect an open or short in the vacuum regulating valve assembly circuit. If the current is out of the standard range, the ECM stores a DTC and illuminates the MIL immediately.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0045 | Turbocharger / Supercharger Boost Control Solenoid Circuit / Open | Open or short in vacuum regulating valve assembly circuit for 0.5 seconds or more.
(1 trip detection logic) |
·
Vacuum regulating valve assembly (for turbocharger control) ·
Open or short in vacuum regulating valve assembly (for turbocharger control) circuit ·
ECM |
Comes on | DTC stored |
If DTC P0045 is stored, the following symptoms may appear.
When the nozzle vane of the turbocharger is stuck closed:
- Vehicle surge when driving with full load
When the nozzle vane of the turbocharger is stuck open:
- Lack of power
- Vehicle surge or hesitation under light or medium load
- White smoke
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0045 | Ignition switch ON for 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the vacuum regulating valve assembly (for turbocharger control).
Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>VACUUM REGULATING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Vacuum Regulating Valve Assembly (for Turbocharger Control)) |
Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B43-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B43-2 - B76-83 (VN) | Always | Below 1 Ω |
| B43-2 or B76-83 (VN) - Body ground | Always | 10 kΩ or higher |
Reconnect the vacuum regulating valve assembly (for turbocharger control) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the vacuum regulating valve assembly (for turbocharger control) connector.
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B43-1 - 3 (EFI-MAIN NO. 2 relay) | Always | Below 1 Ω |
| B43-1 or 3 (EFI-MAIN NO. 2 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 2 relay.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) | Always | Below 1 Ω |
| 1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO. 2 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EFI-MAIN NO. 2 relay.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum regulating valve assembly (for turbocharger control).
Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>VACUUM REGULATING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch to ON for 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT