Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0087  Fuel Rail / System Pressure - Too Low  P0190  Fuel Rail Pressure Sensor Circuit  P0192  Fuel Rail Pressure Sensor Circuit Low Input  P0193  Fuel Rail Pressure Sensor Circuit High Input  


DESCRIPTION

The ECM monitors the internal fuel pressure of the common rail using the fuel pressure sensor, and controls the suction control valve to regulate the internal pressure to the target pressure. The pressure sensor is a semiconductor that varies electrical resistance when pressure is applied to its silicon chip. This sensor outputs the voltage in proportion to the internal fuel pressure.

A208460
2.771,0.5 2.938,0.333 2.938,0.333 2.99,0.333 false 3.135,2.177 3.24,2.125 3.24,2.125 3.281,2.125 false 1.99,1.625 2.188,1.625 false 2.229,1.073 2.552,1.073 false 1.396,0.552 0.938,0.615 false 0.063,0 1.792,0.188 1.729,0.188 10 Property of Output Voltage: 1.052,0.385 1.365,0.542 0.313,0.156 10 5.00 0.615,0.552 0.927,0.708 0.313,0.156 10 4.90 2.219,1.563 2.927,1.823 0.708,0.26 10 PR2 (Sub) 1.563,0.979 2.25,1.135 0.688,0.156 10 RR (Main) 1.063,0.635 1.375,0.792 0.313,0.156 10 4.43 1.052,0.813 1.365,0.969 0.313,0.156 10 3.93 1.052,1.688 1.365,1.844 0.313,0.156 10 1.35 1.052,1.885 1.365,2.042 0.313,0.156 10 0.85 1.052,2.063 1.365,2.219 0.313,0.156 10 0.55 1.24,2.198 1.365,2.354 0.125,0.156 10 0 2.938,2.313 3.438,2.469 0.5,0.156 10 220000 1.583,2.448 2.896,2.625 1.313,0.177 10 Fuel Pressure (kPa) 3.292,2.052 4.188,2.219 0.896,0.167 10 Stores P0192 3.01,0.25 3.906,0.417 0.896,0.167 10 Stores P0193 0.083,1.104 1.323,1.323 1.24,0.219 10 Output Voltage (V) 5.198,1.156 5.552,1.323 0.354,0.167 10 Main 5.26,1.906 5.552,2.073 0.292,0.167 10 Sub 6.76,1.156 7.073,1.344 0.313,0.188 10 PR 6.76,1.354 7.073,1.542 0.313,0.188 10 E2 6.76,1.698 7.073,1.885 0.313,0.188 10 VCS 6.76,1.906 7.073,2.094 0.313,0.188 10 PR2 5.906,0.635 6.146,0.823 0.24,0.188 10 VC 6.375,2.417 6.688,2.604 0.313,0.188 10 E2S 4.292,0.021 6.823,0.49 2.531,0.469 10 Internal Structure of the Pressure Sensor (Duplicate Systems):

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0087 Fuel Rail / System Pressure - Too Low Fuel pressure sensor output voltage stays at fixed value for 90 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

Ran out of fuel

·

Fuel frozen

·

ECM


Comes on DTC stored
P0190 Fuel Rail Pressure Sensor Circuit Fuel pressure sensor output voltage is 0.55 V or less, or 4.9 V or higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0192 Fuel Rail Pressure Sensor Circuit Low Input Fuel pressure sensor output voltage is 0.55 V or less for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Fuel pressure sensor output voltage is 4.9 Vor higher for 0.5 seconds.
(1 trip detection logic)
·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor (common rail assembly)

·

ECM


HINT:

Trouble areas are related to the electrical system only (pumps are not involved)


Comes on DTC stored

Related Data List
DTC No. Data List
P0087
·

Fuel Press

·

Target Common Rail Pressure


P0190
P0192
P0193

HINT:
·

Check Fuel Press compared to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure. Under stable conditions, the difference between Fuel Press and Target Common Rail Pressure is within +/-5000 kPa.

·

For more information on the fuel pressure sensor and common rail system, refer to the System Description (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If DTC P0087 is stored, the following symptoms may appear:

·

Black smoke

·

Poor drivability

·

Lack of power

·

Lack of power due to accelerator restriction of fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, the following symptoms may appear.

·

Lack of power due to accelerator restriction of fail-safe function


·

If DTC P0190, P0192 and/or P0193 is stored, "Fuel Press" always displays 0 kPa or 200000 kPa.



MONITOR DESCRIPTION

P0087 (Fuel pressure sensor output stays at fixed value):
·

Under normal conditions, the internal fuel pressure of the common rail usually fluctuates 1000 to 2000 kPa (10 to 20 kgf/cm2, 145 to 290 psi) even when the driving conditions are constant. This DTC is stored if there is no fluctuation of the fuel pressure. The internal fuel pressure is approximately 27000 to 45000 kPa (275 to 459 kgf/cm2, 3915 to 6525 psi) when idling, and it increases to approximately 45000 to 78000 kPa (459 to 795 kgf/cm2, 6525 to 11310 psi) when running the engine at 3000 rpm.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.

·

The diagram below indicates that fuel pressure rises as engine speed increases, but for the malfunction indicated by this DTC, that does not happen.

A175676
0.058,0.035 1.904,0.244 1.846,0.209 10 P0087 Malfunction Detection 2.267,0.548 3.224,0.769 0.957,0.221 10 Fuel Pressure 4.848,1.68 5.519,1.883 0.671,0.203 10 Abnormal 5.646,0.447 6.226,0.649 0.58,0.201 10 Normal 2.295,2.17 3.245,2.379 0.949,0.209 10 Engine Speed 5.005,0.861 5.429,0.537 false 4.695,1.774 4.184,1.405 false 4.695,1.774 4.832,1.774 false 5.429,0.537 5.629,0.537 false 5.229,3.37 5.615,3.54 0.385,0.17 10 Time



P0190, P0192 and P0193 (Open or short in fuel pressure sensor circuit):

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short malfunction of the sensor circuit.

If these DTCs are stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0087 After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds
P0190 Ignition switch ON for 1 second
P0192
P0193

WIRING DIAGRAM

A149601
0.469,3.26 1.917,3.469 1.448,0.208 10 false Fuel Pressure Sensor 5.604,1.26 6.063,1.469 0.458,0.208 10 false VCM 5.333,1.49 5.51,1.698 0.177,0.208 10 false 68 5.344,0.656 5.521,0.865 0.177,0.208 10 false 66 5.333,1.063 5.51,1.271 0.177,0.208 10 false 67 5.333,2.708 5.51,2.917 0.177,0.208 10 false 69 5.281,1.885 5.615,2.094 0.333,0.208 10 false 114 5.333,2.323 5.51,2.531 0.177,0.208 10 false 91 5.594,0.427 5.99,0.635 0.396,0.208 10 false PCR1 5.594,0.823 6.042,1.031 0.448,0.208 10 false E2M 5.594,2.51 6.042,2.719 0.448,0.208 10 false VCS 5.594,1.677 6.031,1.885 0.438,0.208 10 false PCR2 5.615,2.094 6.208,2.302 0.594,0.208 10 false E2S 1.625,1.385 2.083,1.594 0.458,0.208 10 false VC 1.635,0.552 1.948,0.76 0.313,0.208 10 false PR 1.635,0.969 1.979,1.177 0.344,0.208 10 false E2 1.552,2.635 2,2.844 0.448,0.208 10 false VCS 1.563,1.813 2,2.021 0.438,0.208 10 false PR2 1.573,2.229 2,2.438 0.427,0.208 10 false E2S 1.99,1.042 2.198,1.25 0.208,0.208 10 false 4 1.99,1.479 2.198,1.688 0.208,0.208 10 false 6 1.99,0.635 2.198,0.844 0.208,0.208 10 false 5 1.969,2.74 2.177,2.948 0.208,0.208 10 false 1 1.979,2.354 2.188,2.563 0.208,0.208 10 false 3 2,1.896 2.104,2.104 0.104,0.208 10 false 2 5.99,3.167 6.385,3.365 0.396,0.198 10 false ECM 5.99,3.01 6.292,3.219 0.302,0.208 10 false B76 0.469,3.094 0.75,3.281 0.281,0.188 10 false B70

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC P0190, P0192 or P0193 is output
DTC P0087 is output




DTC P0190, P0192 or P0193 is output

2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

DTC P0087 is output

4.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
2.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B70-5 (PR) - B76-66 (PCR1) Always Below 1 Ω
B70-2 (PR2) - B76-114 (PCR2) Always Below 1 Ω
B70-1 (VCS) - B76-69 (VCS) Always Below 1 Ω
B70-6 (VC) - B76-68 (VCM) Always Below 1 Ω
B70-4 (E2) - B76-67 (E2M) Always Below 1 Ω
B70-3 (E2S) - B76-91 (E2S) Always Below 1 Ω
B70-5 (PR) or B76-66 (PCR1) - Body ground Always 10 kΩ or higher
B70-2 (PR2) or B76-114 (PCR2) - Body ground Always 10 kΩ or higher
B70-1 (VCS) or B76-69 (VCS) - Body ground Always 10 kΩ or higher
B70-6 (VC) or B76-68 (VCM) - Body ground Always 10 kΩ or higher
B70-4 (E2) or B76-67 (E2M) - Body ground Always 10 kΩ or higher
B70-3 (E2S) or B76-91 (E2S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PRESSURE SENSOR)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PRESSURE SENSOR)
a.
A204375
0.479,1.146 0.865,1.385 0.385,0.24 1.958,1.344 2.427,1.583 true 1.427,1.021 1.063,0.781 true 1.948,1.021 2.313,0.74 true 1.427,1.323 0.99,1.646 true 0.219,0.146 0.417,0.323 0.198,0.177 10 *a 2.5,1.521 2.781,1.698 0.281,0.177 10 VC 0.708,0.677 1.073,0.854 0.365,0.177 10 VCS 0.542,1.188 0.854,1.344 0.313,0.156 10 B70 2.385,0.646 2.719,0.844 0.333,0.198 10 E2S 0.75,1.646 0.958,1.802 0.208,0.156 10 E2
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B70-6 (VC) - B70-4 (E2) Ignition switch ON 4.5 to 5.5 V
B70-1 (VCS) - B70-3 (E2S) Ignition switch ON 4.5 to 5.5 V



d.

Reconnect the fuel pressure sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

NG

7.REPLACE ECM
4.REPLACE COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2AD-FHV FUEL>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0087, P0190, P0192, P0193)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

f.

Read the DTCs.

Result:
Proceed to
DTC P0087, P0190, P0192 or P0193 is output
DTC is not output




DTC P0087, P0190, P0192 or P0193 is output

7.REPLACE ECM

DTC is not output

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Let the engine idle for 60 seconds, and then repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds.


h.

Turn the GTS on.


i.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0087, P0190, P0192 and/or P0193.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END