Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The data is used for EGR control, etc.

A128639
1.699,0.22 3.248,0.429 1.55,0.209 10 Throttle Position Sensor 2.898,2.955 3.439,3.157 0.541,0.201 10 Hall IC 4.372,0.59 4.779,0.798 0.407,0.209 10 ECM 4.386,1.016 4.676,1.218 0.29,0.201 10 5 V 3.499,1.116 3.938,1.318 0.439,0.201 10 VCVL 3.574,1.739 4.037,1.94 0.463,0.201 10 VLU 3.499,2.347 3.9,2.549 0.401,0.201 10 EVLU 3.145,1.116 3.408,1.317 0.262,0.201 10 VC 3.145,2.347 3.38,2.549 0.235,0.201 10 E2 3.145,1.739 3.513,1.94 0.368,0.201 10 VTA 1.687,2.975 2.278,3.183 0.591,0.208 10 Magnet 2.521,2.036 2.858,3.036 false 2.415,2.572 2.217,3.063 false 1.687,0.625 2.278,0.833 0.591,0.208 10 Magnet 2.217,0.743 2.415,1.234 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Throttle position sensor output (VLU) is less than 0.2 V for 3 seconds.
(1 trip detection logic)
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VCVL circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Throttle position sensor output (VLU) is more than 4.8 V for 3 seconds.
(1 trip detection logic)
·

Throttle position sensor

·

Open in EVLU circuit

·

VCVL and VLU circuits are short-circuited

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0122 Throttle Sensor Volt %
P0123

HINT:
·

Throttle Sensor Volt %: Throttle position sensor output voltage is converted using 5 V = 100%.

·

When fully closed: 14% or less.

·

When fully open: 70% or more.

·

When the ignition switch is turned from off to ON, the throttle valve fully opens once.

·

When the ignition switch is turned from ON to off, the throttle valve fully closes once.


·

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:

·

Intake booming noise

·

Black smoke

·

Lack of power

·

Vibration at engine stop

·

Turbo overspeed, turbo damage




MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

C129051
2.292,1.063 1.99,1.167 false 2.292,2.708 1.99,2.76 false 4.927,0.438 4.594,1.031 false 4.573,2.688 4.927,3.125 false 0.083,0.042 2.885,0.24 2.802,0.198 10 Throttle Position Sensor Output Voltage (V) 2.063,0.49 2.635,0.688 0.573,0.198 10 Closed 4.979,0.344 5.948,0.542 0.969,0.198 10 Stores P0123 4.01,0.49 4.469,0.688 0.458,0.198 10 Open 2.646,2.719 4.125,2.917 1.479,0.198 10 Range of Operation 4.979,3.063 5.958,3.26 0.979,0.198 10 Stores P0122 2.354,3.365 4.146,3.542 1.792,0.177 10 Throttle Valve Opening Angle 4.083,3.208 4.313,3.406 0.229,0.198 10 70 2.26,3.208 2.396,3.406 0.135,0.198 10 0 1.677,2.677 2.031,2.875 0.354,0.198 10 0.20 1.969,2.406 2.354,2.604 0.385,0.198 10 0.69 1.969,1.375 2.323,1.573 0.354,0.198 10 3.49 1.677,1.063 2.042,1.26 0.365,0.198 10 4.80 1.969,0.844 2.323,1.042 0.354,0.198 10 5.00

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0122 Ignition switch ON for 3 seconds
P0123

WIRING DIAGRAM

A165731
0.583,2.219 2.125,2.396 1.542,0.177 10 false Throttle Position Sensor 5.99,2.156 6.417,2.333 0.427,0.177 10 false ECM 1.552,1.573 1.76,1.719 0.208,0.146 10 false E2 1.479,1.031 1.802,1.177 0.323,0.146 10 false VTA 1.521,0.448 1.76,0.594 0.24,0.146 10 false VC 5.698,1.573 6.115,1.719 0.417,0.146 10 false EVLU 5.698,1.031 6.021,1.177 0.323,0.146 10 false VLU 5.698,0.448 6.125,0.594 0.427,0.146 10 false VCVL 1.865,1.667 1.99,1.844 0.125,0.177 10 false 3 1.854,0.542 1.969,0.719 0.115,0.177 10 false 5 1.844,1.125 1.969,1.302 0.125,0.177 10 false 6 5.406,0.531 5.594,0.708 0.188,0.177 10 false 97 5.344,1.104 5.604,1.281 0.26,0.177 10 false 119 5.417,1.656 5.594,1.833 0.177,0.177 10 false 96 5.99,2 6.26,2.167 0.271,0.167 10 false B76 0.604,2.052 0.792,2.208 0.188,0.156 10 false B3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B3-5 (VC) - B76-97 (VCVL) Always Below 1 Ω
B3-6 (VTA) - B76-119 (VLU) Always Below 1 Ω
B3-3 (E2) - B76-96 (EVLU) Always Below 1 Ω
B3-5 (VC) or B76-97 (VCVL) - Body ground Always 10 kΩ or higher
B3-6 (VTA) or B76-119 (VLU) - Body ground Always 10 kΩ or higher
B3-3 (E2) or B76-96 (EVLU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE POSITION SENSOR)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE POSITION SENSOR)
a.
A275086
0.51,1.063 0.906,1.365 0.396,0.302 1.927,1.417 2.375,1.771 false 1.198,1.833 1.615,1.417 false 0.333,0.438 0.646,0.594 0.313,0.156 10 *a 0.615,1.135 0.927,1.333 0.313,0.198 10 B3 2.271,1.833 2.583,2.031 0.313,0.198 10 VC 1.104,1.854 1.417,2.052 0.313,0.198 10 E2
*a Front view of wire harness connector
(to Throttle Body)


Disconnect the diesel throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B3-5 (VC) - B3-3 (E2) Ignition switch ON 4.98 to 5.02 V



Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Proceed to
DTC P0122 or P0123 is output
DTC is not output




DTC P0122 or P0123 is output

5.REPLACE ECM

DTC is not output

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END