Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P0489  Exhaust Gas Recirculation Control Circuit Low  P0490  Exhaust Gas Recirculation Control Circuit High  


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the EGR body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0489 Exhaust Gas Recirculation Control Circuit Low The EGR actuator current is below 0.5 A for 2.0 seconds during EGR valve operation.
(1 trip detection logic)
·

Open or short in EGR valve circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored
P0490 Exhaust Gas Recirculation Control Circuit High An EGR actuator current of 8 A or higher due to a mechanical malfunction, or the ECM internal circuit temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic)
·

Open or short in EGR valve circuit

·

Electric EGR control valve assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0489
·

Actual EGR Valve Pos.

·

Target EGR Position


P0490

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0489 Idle the engine for 5 seconds or more
P0490

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Inspect the electric EGR valve assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EGR VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)

NG

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ELECTRIC EGR CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-5 (M+) - B76-86 (EGM+) Always Below 1 Ω
i1-1 (M-) - B76-85 (EGM-) Always Below 1 Ω
i1-5 (M+) or B76-86 (EGM+) - Body ground Always 10 kΩ or higher
i1-1 (M-) or B76-85 (EGM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine.


g.

Idle the engine for 5 seconds or more


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EGR VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED