Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P062F  Internal Control Module EEPROM Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P062F Internal Control Module EEPROM Error When any condition below is met (1 trip detection logic):
·

Injector compensation code is not registered.

·

Wrong injector compensation code is registered.

·

Injector pilot quantity learning value is not registered.

·

Catalyst deterioration learning value is not registered.

·

Crank time compensation learning value is not registered.*1

·

Air fuel ratio sensor compensation learning value is not registered.*1


·

Injector compensation code

·

Injector pilot quantity learning value

·

Catalyst thermal deterioration value

·

A/F sensor compensation learning value

·

Crank time compensation learning value

·

ECM


Comes on DTC stored

*1: When this malfunction occurs, the MIL does not illuminate.

NOTICE:
·

When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.

·

Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

·

When a fuel injector is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing fuel injector pilot quantity learning values must be input into the new ECM.

·

When the catalyst converter is replaced, the new catalyst thermal deterioration value must be input into the ECM. When the ECM is replaced, the existing catalyst thermal deterioration value must be input into the new ECM.



HINT:

When replacing the ECM with a new one, if the injector compensation code, injector pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.


When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


a.

Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).


b.

After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION).


c.

Turn the ignition switch off and turn the GTS off.


d.

Wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear the DTC P062F stored in the ECM using the GTS (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>DTC CHECK / CLEAR).

HINT:
·

Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector.

·

When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.

Replacement Part Utility Item
ECM
·

Learning Values Save (Click here (Click here))

·

Learning Values Write (Click here (Click here))


DPNR catalyst Clear DPF Thermal Deterioration Data (Click here (Click here))
Injector
·

Input Injector Compensation Code (Click here (Click here))

·

Pilot Quantity Learning (Click here (Click here))







CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P062F Ignition switch ON for 1 second

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / Learning values confirmation.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242
Result:
Result Proceed to
The injector compensation codes are not input A
The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors
The pilot quantity learning values are set to the default values. B
The catalyst deterioration learning values are set to the default values
Except above C


HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.





A

2.REGISTER INJECTOR COMPENSATION CODE

B

3.LEARNING VALUES WRITE

C

8.CHECK DTC OUTPUT
2.REGISTER INJECTOR COMPENSATION CODE
a.

Register the injector compensation code.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

5.PILOT QUANTITY LEARNING
3.LEARNING VALUES WRITE
HINT:

When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


a.

Install the old ECM.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the intelligent GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Save.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Save
50005 61 240

e.

Remove the old ECM.


f.

Install the new ECM.


g.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Write.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Write
50005 61 241

Result:
Proceed to
NEXT



NEXT

4.LEARNING VALUES CONFIRMATION
4.LEARNING VALUES CONFIRMATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Powertrain / Engine / Utility / Learning Values Confirmation.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242
Result:
Result Proceed to
The pilot quantity learning values are set to the default values. A
The catalyst deterioration learning values are set to the default values B
Except above C


HINT:
·

When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

·

When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.





A

5.PILOT QUANTITY LEARNING

B

6.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.PILOT QUANTITY LEARNING
a.

Perform the pilot quantity learning.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
6.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CATALYST RECORD CLEAR
7.CATALYST RECORD CLEAR
a.

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Read the DTCs.

Result:
Proceed to
DTC is not output
DTC P062F is output




DTC is not output

END

DTC P062F is output

9.REPLACE ECM
9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


f.

Turn the ignition switch to ON for 1 second.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END