Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM C

2AD-FHV ENGINE CONTROL  ECD SYSTEM  P20CB  Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  P20CE  Short in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  


DESCRIPTION

A205137
1.313,1.542 1.271,1.031 1.271,1.031 1.24,1.031 false 2.802,2.26 2.896,2.26 2.896,2.26 3.302,2.094 false 3.125,2.979 2.833,3.271 2.833,3.271 2.781,3.271 false 3.906,1.938 4.125,1.01 4.125,1.01 4.219,1.01 false 3.885,2.531 3.885,2.708 3.885,2.708 3.927,2.708 false 0.219,0.917 1.25,1.271 1.031,0.354 10 false Exhaust Fuel Addition Injector 0.052,1.729 0.875,1.906 0.823,0.177 10 false Exhaust Gas 2.083,0.656 2.979,0.823 0.896,0.167 10 false Turbocharger 4.26,0.927 5.552,1.448 1.292,0.521 10 false Exhaust Gas Temperature Sensor (B1S1) 3.948,2.625 5.604,2.969 1.656,0.344 10 false NO. 2 Exhaust Gas Temperature Sensor (B1S2) 1.188,2.188 2.99,2.625 1.802,0.438 10 false DPNR Catalytic Converter 1.438,3.188 3.708,3.458 2.271,0.271 10 false Air Fuel Ratio Sensor 5.948,1.802 6.292,1.969 0.344,0.167 10 false ECM

The exhaust fuel addition injector is mounted on the exhaust port of the cylinder head, and low pressure fuel is provided to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.

This injector is used for two different controls: PM forced regeneration and nitrogen oxide (NOx) reduction.

Under the PM forced regeneration control, the injector adds fuel to raise the catalyst temperature.

In nitrogen oxide (NOx) reduction control, the injector helps the air-fuel ratio become rich. As a result, NOx in the exhaust gas will be reduced in response to the rich air-fuel ratio.

HINT:
·

For more information on the exhaust fuel addition injector and TOYOTA D-CAT*, refer to the following procedures (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

·

If P20CB, P20CD and P20CE are present, refer to the DTC table for TOYOTA D-CAT (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION).

*: Diesel Clean Advanced Technology.




DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CB Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is low for 3 seconds.
(1 trip detection logic)
·

Open in exhaust fuel addition injector circuit

·

Exhaust fuel addition injector

·

ECM


Comes on DTC stored
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is high for 0.16 seconds.
(1 trip detection logic)
·

Open in exhaust fuel addition injector circuit

·

Exhaust fuel addition injector

·

ECM


Comes on DTC stored
P20CE Short in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector on, the FIVM1 output is low and the FIVM2 output is low 7 or more times.
(1 trip detection logic)
·

Open in exhaust fuel addition injector circuit

·

Exhaust fuel addition injector

·

ECM


Comes on DTC stored

HINT:

DTC P200C, P200E and/or P20CF will be present if there is an open malfunction in the exhaust fuel addition injector circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVM) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector via a drive circuit inside the ECM. The FIVM signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVM signal, the ECM judges that the current has been applied to the exhaust fuel addition injector.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVM are inconsistent.

A117827
2.76,0.348 3.107,0.528 0.347,0.18 10 ECM 1.226,0.809 1.556,0.949 0.331,0.14 10 CPU 1.306,1.176 1.774,1.336 0.469,0.159 10 FIVM 1 1.306,2.061 1.774,2.221 0.469,0.159 10 FIVM 2 1.526,2.952 1.776,3.111 0.251,0.159 10 FIV 3.222,1.091 4.254,1.271 1.032,0.18 10 Monitor Circuit 1 3.222,1.97 4.254,2.149 1.032,0.18 10 Monitor Circuit 2 3.184,2.853 4.293,3.032 1.108,0.18 10 Command Circuit 5.474,1.995 7.013,2.165 1.539,0.17 10 to Fuel Addition Injector

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CB Ignition switch ON for 3 seconds
P20CD
P20CE Drive vehicle for 20 minutes (exhaust gas temperature is 250°C (482°F) or higher).

WIRING DIAGRAM

A284163
3.073,1.469 5.75,1.698 2.677,0.229 10 false Exhaust Fuel Addition Injector Assembly 5.75,1.031 6.448,1.333 0.698,0.302 10 false FIV 1.281,0.906 1.552,1.125 0.271,0.219 10 false 5 0.604,2.344 1.823,2.542 1.219,0.198 10 false EFI-MAIN NO. 2 1.219,1.719 2.438,1.917 1.219,0.198 10 false EFI-MAIN NO. 2 5.406,1.031 5.771,1.25 0.365,0.219 10 false B76 5.417,2.146 5.781,2.365 0.365,0.219 10 false A61 5.448,0.844 5.813,1.063 0.365,0.219 10 false 105 5.458,1.969 5.823,2.188 0.365,0.219 10 false 45 5.74,2.042 6.438,2.344 0.698,0.302 10 false MREL 2.604,0.844 3.385,1.031 0.781,0.188 10 false EFI NO. 1 1.281,1.417 1.552,1.635 0.271,0.219 10 false 2 2.115,1.417 2.385,1.635 0.271,0.219 10 false 1 2.125,0.927 2.396,1.146 0.271,0.219 10 false 3 4.719,0.896 4.99,1.115 0.271,0.219 10 false 1 3.719,0.896 3.99,1.115 0.271,0.219 10 false 2 3.188,1.281 3.5,1.438 0.313,0.156 10 false B55 0.552,3.031 1.771,3.229 1.219,0.198 10 false FL MAIN 6.125,3.885 6.542,4.406 0.417,0.521 10 false ECM 0.781,3.74 2,3.938 1.219,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)

NG

12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)
a.
A204917
0.417,1.042 0.813,1.302 0.396,0.26 0.396,0.25 0.615,0.438 0.219,0.188 10 *a 0.458,1.083 0.823,1.229 0.365,0.146 10 B55
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


Disconnect the exhaust fuel addition injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B55-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B55-1 - B76-105 (FIV) Always Below 1 Ω
B55-1 or B76-105 (FIV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B55-2 - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B55-2 or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 2 RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

10.REPLACE EFI-MAIN NO. 2 RELAY
7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END