The No. 1 vacuum switching valve (for EGR cooler) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P245C | EGR Cooler Bypass Control Circuit Low | Open or short in the No. 1 vacuum switching valve (for EGR cooler) for 3 seconds.
(1 trip detection logic) |
·
Open or short in No. 1 vacuum switching valve (for EGR cooler) circuit ·
No. 1 vacuum switching valve (for EGR cooler) ·
ECM |
Comes on | DTC stored |
| P245D | EGR Cooler Bypass Control Circuit High | Open or short in the No. 1 vacuum switching valve (for EGR cooler) for 3 seconds.
(1 trip detection logic) |
·
Open or short in No. 1 vacuum switching valve (for EGR cooler) circuit ·
No. 1 vacuum switching valve (for EGR cooler) ·
ECM |
Comes on | DTC stored |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P245C | Ignition switch ON for 3 seconds |
| P245D |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
Inspect the No. 1 vacuum switching valve (for EGR cooler).
Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Vacuum Switching Valve (for EGR cooler)) |
Disconnect the No. 1 vacuum switching valve (for EGR cooler) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B56-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 vacuum switching valve (for EGR cooler) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B56-2 - B76-106 (ECBV) | Always | Below 1 Ω |
| B56-2 or B76-106 (ECBV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the NO.1 vacuum switching valve (for EGR cooler) connector.
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B56-1 - 3 (EFI-MAIN NO. 2 relay) | Always | Below 1 Ω |
| B56-1 or 3 (EFI-MAIN NO. 2 relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI-MAIN NO. 2 relay.
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) | Always | Below 1 Ω |
| 1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (EFI-MAIN NO. 2 relay) - Body ground | Always | Below 1 Ω |
| Result |
|---|
| OK |
| NG |
OK
NG
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EFI-MAIN NO. 2 relay.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 vacuum switching valve (for EGR cooler).
Click hereEngine / Hybrid System>2AD-FHV EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch to ON for 3 seconds.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT