Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD(for Dual Type)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0059590 STEERING PAD(for Dual Type) A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD(for Dual Type)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45186 3.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B342172C01
0.625,1.583 1.313,0.813 true 0.479,1.563 0.792,1.719 0.313,0.156 10 *1
*1 Protective Tape


Using a screwdriver, detach the claw and guide to remove the lower No. 2 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



Hide 45130 4.REMOVE STEERING PAD ASSEMBLY

CAUTION:

When storing the steering pad, keep the airbag deployment side facing upward.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Using a T30H "TORX" screwdriver, push in the 3 torsion springs to detach the 3 claws.

NOTICE:
·

Do not drop the steering pad assembly.

·

When disconnecting the steering pad, do not pull the airbag wire harness.



HINT:

Insert the T30H "TORX" screwdriver from the installation hole for thr lower No. 2 steering wheel cover and 2 service holes.


B339259C01
4.365,1.448 4.771,1.25 true 6.177,1.125 6.458,0.958 true 5.75,0.438 6.021,0.583 true 1.958,1.906 1.875,1.729 true 1.781,2.281 1.344,2.135 true 0.833,0.948 1.135,1.146 true 1.302,0.552 1.563,0.469 true 5.563,0.313 5.875,0.469 0.313,0.156 10 false *1 4.792,1.135 5.104,1.292 0.313,0.156 10 false *2 1.75,1.563 2.063,1.719 0.313,0.156 10 false *1 1.563,0.344 1.875,0.5 0.313,0.156 10 false *1 1.823,2.219 2.135,2.375 0.313,0.156 10 false *2 0.667,0.813 0.979,0.969 0.313,0.156 10 false *2 6.469,0.833 6.781,0.99 0.313,0.156 10 false *2
*1 Torsion Spring *2 T30H "TORX" Screwdriver



d.
B341163C01
0.99,1.813 2,0.865 true 0.667,2.917 0.917,2.615 true 1.604,0.094 1.917,0.25 0.313,0.156 10 *1 1.302,1.146 1.615,1.302 0.313,0.156 10 *2 0.521,2.927 0.833,3.083 0.313,0.156 10 *3 0.813,1.781 1.042,2.031 0.229,0.25 10 *4 2.135,0.688 2.448,0.844 0.313,0.156 10 *2
*1 Horn Connector
*2 Airbag Connector
*3 Connector Lock
*4 Protective Tape


Disconnect the horn connector from the steering pad assembly.


e.

Using a screwdriver, release the 2 airbag connector locks.

HINT:

Tape the screwdriver tip before use.



f.

Disconnect the 2 airbag connectors to remove the steering pad assembly as shown in the illustration.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.