Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).
(a) Vehicle speed is 20 km/h (12.43 mph) or more.
(b) Engine speed is 1000 rpm or higher.
(c) STA signal is on.
·

Park/neutral position switch assembly

·

Starter relay (ST) circuit

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) Starter relay (ST)
Park/neutral position switch assembly
Ignition switch assembly
Certification ECU
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter On

CONFIRMATION DRIVING PATTERN

A231469
1.229,1.979 1.656,2.198 0.427,0.219 10 Idling 0.396,2.26 1.604,2.583 1.208,0.323 10 Ignition Switch ON 1.063,0.865 1.635,1.073 0.573,0.208 10 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 20 seconds or more 2.01,2.333 2.302,2.552 0.292,0.219 10 [A] 2.615,2.125 2.823,2.302 0.208,0.177 10 [B] 4.063,0.458 4.292,0.625 0.229,0.167 10 [C] 4.885,3.333 5.115,3.5 0.229,0.167 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0617.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A299795
0.083,0.073 2.188,0.281 2.104,0.208 12 false w/o Entry and Start System: 0.5,2.271 0.875,2.469 0.375,0.198 10 false AM2 1.25,1.333 1.625,1.531 0.375,0.198 10 false G4 1.25,1.5 2.833,1.698 1.583,0.198 10 false Ignition Switch Assembly 1.583,1.052 1.958,1.25 0.375,0.198 10 false AM2 2.208,1.052 2.583,1.25 0.375,0.198 10 false ST2 1.417,1.052 1.583,1.25 0.167,0.198 10 false 4 2.583,1.052 2.75,1.25 0.167,0.198 10 false 2 5.448,0.917 5.698,1.115 0.25,0.198 10 false 63 5.417,1.135 5.75,1.333 0.333,0.198 10 false B77 5.75,1.135 6.167,1.333 0.417,0.198 10 false NSW 3.667,2.167 3.833,2.365 0.167,0.198 10 false 9 4.583,2.167 4.75,2.365 0.167,0.198 10 false 4 4.385,2.198 4.552,2.396 0.167,0.198 10 false B 3.875,2.198 4.042,2.396 0.167,0.198 10 false L 3.25,2.417 3.542,2.583 0.292,0.167 10 false B36 3.25,2.583 5.667,2.75 2.417,0.167 10 false Park/Neutral Position Switch Assembly 3.458,4.531 3.833,4.729 0.375,0.198 10 false ST 0.531,4.75 1.115,4.917 0.583,0.167 10 false FL MAIN 0.667,6.75 1.167,7 0.5,0.25 10 false Battery 1.594,3.854 1.969,4.052 0.375,0.198 10 false ST 1.333,6.667 2.5,6.917 1.167,0.25 10 false Starter Assembly 2.01,5.427 2.24,5.594 0.229,0.167 10 false B6 1.292,5.833 1.521,6 0.229,0.167 10 false C5 1.333,5.656 1.521,5.823 0.188,0.167 10 false 1 2.313,5.427 2.5,5.594 0.188,0.167 10 false 1 3.229,5 3.417,5.167 0.188,0.167 10 false 1 3.25,4 3.438,4.167 0.188,0.167 10 false 2 2.729,5 2.917,5.167 0.188,0.167 10 false 3 2.729,4 2.917,4.167 0.188,0.167 10 false 5 5.417,3.698 5.708,3.865 0.292,0.167 10 false A62 5.448,3.469 5.698,3.667 0.25,0.198 10 false 22 5.75,3.552 6.167,3.75 0.417,0.198 10 false STA 6.167,4.917 6.583,5.115 0.417,0.198 10 false ECM

A299796
0.083,0.063 2.052,0.292 1.969,0.229 12 false w/ Entry and Start System: 0.167,2.167 0.5,2.365 0.333,0.198 10 false G82 0.167,2.333 2,2.75 1.833,0.417 10 false Certification ECU (Smart Key ECU Assembly) 1.333,0.865 1.667,1.063 0.333,0.198 10 false NE 1.167,1.313 1.583,1.51 0.417,0.198 10 false STAR 1.25,1.74 1.583,1.938 0.333,0.198 10 false STA 1.667,1.198 1.917,1.396 0.25,0.198 10 false 5 1.667,0.74 1.917,0.938 0.25,0.198 10 false 16 1.667,1.604 1.917,1.802 0.25,0.198 10 false 7 3.5,2.302 3.75,2.5 0.25,0.198 10 false 9 4.417,2.302 4.667,2.5 0.25,0.198 10 false 4 3.083,2.667 3.417,2.833 0.333,0.167 10 false B36 3.083,2.833 5.583,3.031 2.5,0.198 10 false Park/Neutral Position Switch Assembly 3.708,2.333 3.958,2.531 0.25,0.198 10 false L 4.208,2.333 4.458,2.531 0.25,0.198 10 false B 5.427,0.875 5.76,1.073 0.333,0.198 10 false A62 5.469,0.656 5.719,0.854 0.25,0.198 10 false 45 6.167,5.5 6.583,5.865 0.417,0.365 10 false ECM 5.833,0.865 6.25,1.115 0.417,0.25 10 false NEO 5.427,1.323 5.76,1.521 0.333,0.198 10 false B77 5.458,1.115 5.708,1.313 0.25,0.198 10 false 63 5.833,1.323 6.25,1.573 0.417,0.25 10 false NSW 5.833,4.167 6.167,4.365 0.333,0.198 10 false STA 5.427,4.281 5.76,4.479 0.333,0.198 10 false A62 5.469,4.073 5.719,4.271 0.25,0.198 10 false 22 0.417,4.385 0.75,4.583 0.333,0.198 10 false ST 3,4.969 3.333,5.167 0.333,0.198 10 false ST 0.458,5.229 1.042,5.396 0.583,0.167 10 false FL MAIN 0.594,6.885 1.177,7.052 0.583,0.167 10 false Battery 1.083,6.917 2.25,7.167 1.167,0.25 10 false Starter Assembly 2.75,4.5 2.917,4.667 0.167,0.167 10 false 2 2.198,4.5 2.365,4.667 0.167,0.167 10 false 5 2.198,5.417 2.365,5.583 0.167,0.167 10 false 3 2.75,5.417 3,5.583 0.25,0.167 10 false 1 1.802,5.885 2.052,6.052 0.25,0.167 10 false B6 1.083,6.104 1.333,6.271 0.25,0.167 10 false C5 2.104,5.875 2.354,6.042 0.25,0.167 10 false 1 1.115,5.917 1.365,6.083 0.25,0.167 10 false 1

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Result:
Condition Starter Signal Result
Driving at 20 km/h (12.4 mph) or more OFF A
ON B




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace harness or connector (starter signal circuit).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0617 is output A
DTC is not output B




A

B

END