Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction ECM Comes on DTC stored

DTC No. Monitoring Item Detection Timing Detection Logic
P2610 Soak timer (built into ECM) Engine running 2 trip

DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A290317
4.167,0.833 4.583,1 0.417,0.167 10 false IGSW 4.333,2.667 4.583,2.833 0.25,0.167 10 false +B 4.167,3.469 4.583,3.635 0.417,0.167 10 false MREL 5,1.25 5.75,1.583 0.75,0.333 10 false Soak Timer IC 5,2.583 5.667,2.917 0.667,0.333 10 false Power Source IC 5,3.417 5.833,3.75 0.833,0.333 10 false MAIN Relay Control IC 5.5,4.333 5.917,4.5 0.417,0.167 10 false ECM 3.938,1.135 4.271,1.302 0.333,0.167 10 false IGN 2.917,1.75 3.25,1.917 0.333,0.167 10 false IG2 2.583,3.958 3.667,4.125 1.083,0.167 10 false EFI-MAIN NO. 1 1.99,1.135 2.323,1.302 0.333,0.167 10 false IG2 0.667,2.104 3.917,2.5 3.25,0.396 10 false from Ignition Switch Assembly*1 or Certification ECU (Smart key ECU Assembly)*2 0.583,3.167 1.417,3.333 0.833,0.167 10 false from Battery 0.333,4.417 2.333,4.667 2,0.25 10 false *1: w/o Entry and Start System 2.417,4.417 4.417,4.667 2,0.25 10 false *2: w/ Entry and Start System 1.75,3.333 2.833,3.5 1.083,0.167 10 false EFI-MAIN NO. 1 0.583,0.979 1.417,1.146 0.833,0.167 10 false from Battery

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 minutes or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P2610.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:

If the judgment result shows ABNORMAL, the system has a malfunction.



CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and wait for 10 minutes or more.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


j.

If no pending DTC is output, the repair has been successfully completed.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END