The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON. 2.
One of the following conditions is met: (a) 2 or more of the P, N, NSW, R and D shift lever position signals are on simultaneously. (b) The P, N, NSW, R and D shift lever position signals are all off simultaneously. (c) The P, N, NSW or R shift lever position signal is on when the shift lever is in M. 3.
2 seconds for conditions (a) and (c) above, and 60 seconds for condition (b) above 4.
2 trip detection logic |
·
Open or short in park/neutral position switch circuit ·
Park/neutral position switch assembly ·
Transmission control switch (Transmission floor shift assembly) ·
ECM |
Comes on | DTC stored |
This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or M).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Sports Mode Selection SW |
| Shift SW Status (D Range) |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect. |
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B36-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| B36-1 (RB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B36-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| B36-4 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch Assembly) |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (RB) - 3 (PL) | Shift lever in P | Below 1 Ω |
| 4 (B) - 9 (L) | Shift lever in P | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| 1 (RB) - 8 (NL) | Shift lever in N | Below 1 Ω |
| 4 (B) - 9 (L) | Shift lever in N | Below 1 Ω |
| 1 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| 1 (RB) - 3 (PL) | Shift lever not in P | 10 kΩ or higher |
| 4 (B) - 9 (L) | Shift lever not in P | 10 kΩ or higher |
| 1 (RB) - 2 (RL) | Shift lever not in R | 10 kΩ or higher |
| 1 (RB) - 8 (NL) | Shift lever not in N | 10 kΩ or higher |
| 4 (B) - 9 (L) | Shift lever not in N | 10 kΩ or higher |
| 1 (RB) - 7 (DL) | Shift lever not in D, M, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transmission Control Switch) |
Disconnect the transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G36-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| G36-4 (IG) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Transmission Control Switch) |
Disconnect the transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| 4 (IG) - 5 (S) | Shift lever not in M, "+" or "-" | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B75-99 (P) - Body ground | ·
Ignition switch ON ·
Shift lever in P |
11 to 14 V |
| B75-79 (R) - Body ground | ·
Ignition switch ON ·
Shift lever in R |
11 to 14 V |
| B75-97 (N) - Body ground | ·
Ignition switch ON ·
Shift lever in N |
11 to 14 V |
| B75-81 (D) - Body ground | ·
Ignition switch ON ·
Shift lever in D |
11 to 14 V |
| A62-41 (S) - Body ground | ·
Ignition switch ON ·
Shift lever in M, "+" or "-" |
11 to 14 V |
| B75-99 (P) - Body ground | ·
Ignition switch ON ·
Shift lever not in P |
Below 1 V |
| B75-79 (R) - Body ground | ·
Ignition switch ON ·
Shift lever not in R |
Below 1 V |
| B75-97 (N) - Body ground | ·
Ignition switch ON ·
Shift lever not in N |
Below 1 V |
| B75-81 (D) - Body ground | ·
Ignition switch ON ·
Shift lever not in D |
Below 1 V |
| A62-41 (S) - Body ground | ·
Ignition switch ON ·
Shift lever not in M, "+" or "-" |
Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the B36 park/neutral position switch connector.
Disconnect the B75 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B36-4 (B) - B75-63 (NSW) | Always | Below 1 Ω |
| B36-4 (B) - Body ground | Always | 10 kΩ or higher |
| B75-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG