The ECM uses shift solenoid valves SL and DSU to perform lock-up control in response to the driving conditions.
If any parts inside the torque converter assembly are damaged, DTC P0741/64 and P2757/64 could be output. In this case, make sure to replace both the torque converter assembly and the continuously variable transaxle assembly as broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.
Shift solenoid valve DSU controls the lock-up clutch pressure in response to the input torque.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0741 | Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D. 2.
The lock-up signal is on, but lock-up is off. 3.
- 4.
2 trip detection logic |
·
Continuously variable transaxle assembly ·
Torque converter assembly |
Comes on | DTC stored |
| P2757 | Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU) | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.2 mph) or more with the shift lever in D. 2.
The lock-up signal is on, but lock-up is off. 3.
- 4.
2 trip detection logic 1.
The engine is warmed up, and the vehicle is driven at a speed of 8 km/h (5.0 mph) or more with the shift lever in D. 2.
The lock-up signal is off, but lock-up is on. 3.
- 4.
2 trip detection logic |
·
Continuously variable transaxle assembly ·
Torque converter assembly |
Comes on | DTC stored |
When performing lock-up control (on/off) of the torque converter, the ECM compares the rotating speeds of the turbine (NT) and engine (NE) to detect mechanical malfunctions in the shift solenoid valves SL and DSU. When the rotating speeds are different than expected, the ECM detects the problem, illuminates the MIL and stores the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Proceed to |
|---|
| Only P0741 and/or P2757 is output |
| P0741 and/or P2757 and other DTCs are output |
If any other DTCs besides P0741 or P2757 are output, perform troubleshooting for those DTCs first.
Only P0741 and/or P2757 is output
P0741 and/or P2757 and other DTCs are output
Clear the DTC.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Oil seal |
| *a | Example of the damage |
| *b | Damage |
Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.
This test must be conducted after checking and confirming that the engine is operating normally.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform the test with the A/C off and no electrical load.
Make sure to replace both the torque converter assembly and the continuously variable transaxle assembly if any parts inside the torque converter assembly are damaged. Broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.
Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.
Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.
The lock-up off vehicle speed may vary depending on the electrical load, air conditioning and brake operations.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, SPD (NT) and Lock Up.
| Tester Display |
|---|
| Engine Speed |
| SPD (NT) |
| Lock Up |
Check the Data List while driving.
| Result | Proceed to |
|---|---|
| When the lock-up is on, the turbine speed is lower than the engine speed. | A |
| When the lock-up is off, the turbine speed is equal to the engine speed. | |
| When the lock-up is on, the turbine speed is equal to the engine speed. | B |
| When the lock-up is off, the turbine speed is lower than the engine speed. |
A
B
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the torque converter assembly.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT