Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0047069 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 16282 2.DISCONNECT WATER BY-PASS HOSE

C199724

a.

Slide the 2 clips and disconnect the 2 water bypass hoses from the oil cooler.


Hide 28100 3.REMOVE STARTER ASSEMBLY

Hide 12325A 4.REMOVE ENGINE MOUNTING BRACKET LH

C200323

a.

Remove the 3 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.


Hide 12311A 5.REMOVE FRONT ENGINE MOUNTING BRACKET

C200325

a.

Remove the 3 bolts and front engine mounting bracket from the continuously variable transaxle assembly.


Hide 12321A 6.REMOVE REAR ENGINE MOUNTING BRACKET

C200327

a.

Detach the engine wire clamp from the rear engine mounting bracket.


b.

Remove the 3 bolts and rear engine mounting bracket from the continuously variable transaxle assembly.


Hide 7.REMOVE GROUND CABLE

C200329

a.

Detach the clamp.


b.

Remove the bolt and ground cable.


Hide 82121 8.DISCONNECT ENGINE WIRE

C200331C01
0.146,0.094 0.5,0.385 0.354,0.292 10 false *a 4.031,0.083 4.469,0.302 0.438,0.219 10 false *b
*a for Front Side *b for Rear Side


a.

for Front Side:

Disconnect the transmission wire connector, park/neutral position switch connector, and 3 revolution sensor connectors, and detach the 3 wire harness clamps from the continuously variable transaxle assembly.


b.

for Rear Side:

Disconnect the oil pressure sensor connector and detach the 2 wire harness clamps from the continuously variable transaxle assembly.


Hide 32101A 9.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

C279068

a.

Remove the flywheel housing under cover.


b.

Turn the crankshaft to gain access to the location of the 6 drive plate and torque converter assembly setting bolts and each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There is one black colored bolt.



Hide 30400 10.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

C169063

a.

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



Hide 33823 11.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C200333

a.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 12.REMOVE WIRE HARNESS CLAMP BRACKET AND TRANSMISSION CONTROL CABLE SUPPORT

C281496

a.

Detach the water by-pass hose clamp from the wire harness clamp bracket.


b.

Remove the 4 bolts, 3 wire harness clamp brackets and transmission control cable support from the continuously variable transaxle assembly.


Hide 32000A 13.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the continuously variable transaxle assembly.


Hide 30400E 14.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is the possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from running, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, etc.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque convertor is not attached to it.

·

Do not use the air gun until the torque convertor has been installed, as it could cause dust and foreign matter to be stirred up.



a.
C208788E02
2.261,2.531 2.581,2.825 0.320,0.295 10 SST 2.442,1.881 2.442,2.501 false

Clean the tips of both the claws of SST and the center bolt.


b.

Using SST, remove the CVT oil pump type T oil seal.

SST
09308-10010  

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.