Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0060958 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0841  Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance  P2829  Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM controls the secondary oil pressure calibration based on the secondary oil pressure signal detected by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0841 Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The requested oil pressure value is 0.5 MPa or less.

2.

The oil pressure sensor output value is 3.0 MPa or higher.

3.

3 seconds

4.

2 trip detection logic


·

Oil pressure sensor

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored
P2829 Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The requested oil pressure value is 0.5 MPa or less.

2.

The oil pressure sensor output value is 3.0 MPa or higher.

3.

3 seconds

4.

2 trip detection logic


1.

Shift lever in D, and driving at speed of 8 km/h (5 mph) or less.

2.

The ratio of the rotation speeds of the primary pulley (NIN) and secondary pulley (NOUT) exceeds the threshold.

3.

0.2 second

4.

2 trip detection logic


·

Oil pressure sensor

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure or low-pressure errors. When a mechanical malfunction is detected at shift solenoid valve SLS and at the oil pressure sensor, the ECM detects the problem, illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Proceed to
Only P0841 and/or P2829 is output
P0841 and/or P2829 and other DTCs are output


HINT:

If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.




Only P0841 and/or P2829 is output

2.READ VALUE USING GTS (A/T OIL PRESSURE)

P0841 and/or P2829 and other DTCs are output

2.READ VALUE USING GTS (A/T OIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value min.: -64 MPa
max.: 63.998 MPa
Secondary oil pressure inspection
·

D position stall speed test: 3.2 to 4.5 MPa

·

R position stall speed test: 3.0 to 3.5 MPa


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Proceed to
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition




Data displayed is not as specified under Normal Condition

3.REPLACE OIL PRESSURE SENSOR

Data displayed is as specified under Normal Condition

3.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

5.PERFORM INITIALIZATION
5.PERFORM INITIALIZATION
a.

Using the GTS, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Proceed to
P0841 and/or P2829 is output
DTC is not output




P0841 and/or P2829 is output

7.REPLACE ECM

DTC is not output

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION
a.

Using the GTS, perform reset memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Proceed to
P0841 and/or P2829 is output
DTC is not output




P0841 and/or P2829 is output

10.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

DTC is not output

END

10.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CLEAR DTC
11.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT