The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly)*1 or deceleration sensor*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1585 | Acceleration Sensor Circuit | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON. 2.
The output value of the yaw rate and acceleration sensor*1 or deceleration sensor*2 remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds. 3.
0.5 seconds 4.
1 trip detection logic 1.
The ignition switch is ON. 2.
The power source voltage to the yaw rate and acceleration sensor*1 or deceleration sensor*2 remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds. 3.
0.5 seconds 4.
1 trip detection logic 1.
The ignition switch is ON. 2.
No signal from the yaw rate and acceleration sensor*1 or deceleration sensor*2 is detected 7 times or more. 3.
0.5 seconds 4.
1 trip detection logic 1.
The ignition switch is ON. 2.
With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G. 3.
0.5 seconds 4.
1 trip detection logic 1.
The ignition switch is ON. 2.
A yaw rate and acceleration sensor*1 or deceleration sensor*2 power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more. 3.
0.5 seconds 4.
1 trip detection logic |
·
Yaw rate and acceleration sensor (Airbag sensor assembly)*1 ·
Deceleration sensor*2 ·
Skid control ECU (Brake actuator assembly) ·
CAN communication system |
- | DTC stored |
*1: w/ VSC
*2: w/o VSC
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If a CAN communication DTC is output, perform troubleshooting for that DTC first.
Check for DTCs of the CAN communication system.
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output |
DTCs are not output
DTCs are output
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| G Sensor |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of deceleration sensor | min.: 0 V
max.: 79.998 V |
Displays converted voltage of deceleration sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
In accordance with the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| Data displayed is as specified under Normal Condition (w/ VSC) | A |
| Data displayed is as specified under Normal Condition (w/o VSC) | B |
| Data displayed is not as specified under Normal Condition (w/ VSC) | C |
| Data displayed is not as specified under Normal Condition (w/o VSC) | D |
A
B
C
D
Replace the skid control ECU (brake actuator assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the N5 deceleration sensor connector.
Disconnect the A63 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N5-1 (GL1) - A63-3 (GL1) | Always | Below 1 Ω |
| N5-2 (GGND) - A63-15 (GGND) | Always | Below 1 Ω |
| N5-3 (VGS) - A63-26 (VGS) | Always | Below 1 Ω |
| N5-1 (GL1) or A63-3 (GL1) - Body ground | Always | 10 kΩ or higher |
| N5-2 (GGND) or A63-15 (GGND) - Body ground | Always | 10 kΩ or higher |
| N5-3 (VGS) or A63-26 (VGS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Deceleration Sensor) |
Disconnect the deceleration sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N5-3 (VGS) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Deceleration Sensor) |
Remove the deceleration sensor.
Connect 3 dry cell batteries of 1.5 V in series.
Connect the positive (+) lead of the batteries to terminal 3 (VGS) and the negative (-) lead to terminal 2 (GGND) to apply a voltage of 4.5 V.
Do not apply 6 V or higher to terminals 3 (VGS) and 2 (GGND).
If the sensor is dropped, replace it with a new one.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (GL1) - 2 (GGND) | ·
4.5 V applied to terminals 3 (VGS) and 2 (GGND) ·
Sensor not tilted |
Approx. 2.5 V |
| 1 (GL1) - 2 (GGND) | ·
4.5 V applied to terminals 3 (VGS) and 2 (GGND) ·
Sensor tilted back and forth |
Changes between approx. 0.5 V and 4.5 V |
If the sensor is tilted too much, it may output the wrong value.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the deceleration sensor.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>DECELERATION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT