Home › Drivetrain › K111 MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008435 K111 MULTIDRIVE / CVT _0060958 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P282B  Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM uses shift solenoid valve SLS to control the secondary pulley pressure and belt clamping pressure according to the input shaft torque. Additionally, shift solenoid valve SLS is used to control the forward and reverse clutch hydraulic pressure when the forward and reverse clutch is engaged.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P282B Pressure Control Solenoid "K" Electrical (Shift Solenoid Valve SLS) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The vehicle is being driven.

2.

There is an open or short circuit in the shift solenoid valve SLS circuit.

3.

1 second

4.

1 trip detection logic


·

Open or short in shift solenoid valve SLS circuit

·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the shift solenoid valve SLS circuit. When there is an open or short circuit in the shift solenoid valve SLS circuit, the ECM detects the problem, illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C251557E08
5.792,3 6.156,3.198 0.365,0.198 10 B75 5.792,3.198 6.188,3.417 0.396,0.219 10 ECM 0.344,2.74 0.708,2.938 0.365,0.198 10 B37 0.333,2.958 4.375,3.229 4.042,0.271 10 Transmission Wire (Continuously Variable Transaxle Assembly) 5.615,1.26 6.094,1.469 0.479,0.208 10 SLS+ 5.625,2.229 6.063,2.448 0.438,0.219 10 SLS- 5.302,1.375 5.552,1.615 0.25,0.24 10 73 5.281,2.344 5.563,2.604 0.281,0.26 10 72 3.927,1.375 4.135,1.573 0.208,0.198 10 3 3.927,2.344 4.135,2.542 0.208,0.198 10 8 3.438,1.115 3.917,1.313 0.479,0.198 10 SLS+ 3.448,2.083 3.927,2.313 0.479,0.229 10 SLS- 1.51,1.74 3.219,2.01 1.708,0.271 10 Shift Solenoid Valve SLS

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLS)
a.
C199169C09
1.708,0.948 0.875,0.458 true 0.875,1.781 1.719,1.25 true 0.427,0.375 0.865,0.615 0.438,0.24 10 SLS+ 0.115,0.094 0.427,0.292 0.313,0.198 10 *a 0.448,1.708 0.854,1.938 0.406,0.229 10 SLS-
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SLS+) - 8 (SLS-) 20°C (68°F) 5.1 to 5.5 Ω
3 (SLS+) - Body ground Always 10 kΩ or higher
8 (SLS-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C267934C18
1.49,0.135 1.938,0.385 0.448,0.25 1.531,1.771 1.188,1.01 true 0.833,1.781 1.125,1.01 true 1.604,0.177 2.063,0.375 0.458,0.198 10 B75 0.49,1.854 1.208,2.104 0.719,0.25 10 72 (SLS-) 1.323,1.854 2.042,2.104 0.719,0.25 10 73 (SLS+) 0.115,0.083 0.385,0.323 0.271,0.24 10 *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-73 (SLS+) - B75-72 (SLS-) 20°C (68°F) 5.0 to 5.6 Ω
B75-73 (SLS+) - Body ground Always 10 kΩ or higher
B75-72 (SLS-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT