Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0061120 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C228973E02
4.635,1.219 4.427,0.583 4.427,0.583 4.302,0.583 true 4.417,1.427 4.229,2.021 4.229,2.021 4.104,2.021 true 5.698,1.448 5.5,2.021 5.5,2.021 5.365,2.021 true 0.219,0.354 1.479,0.552 1.26,0.198 10 Hydraulic Pressure 2.75,2.375 3.313,2.573 0.563,0.198 10 Current 3.5,0.49 4.323,0.688 0.823,0.198 10 Spool Valve 3.615,1.927 4.125,2.125 0.51,0.198 10 Sleeve 4.49,1.927 5.375,2.125 0.885,0.198 10 Solenoid Coil

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) The ECM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed between the turbine and output shaft, and also by the ATF pressure (2-trip detection logic).
·

Shift solenoid valve SLT remains open

·

Shift solenoid valve SL1, SL2, SL3 or SL4 remains open or closed

·

Transmission valve body assembly is blocked

·

Automatic transaxle assembly (clutch, brake or gear, etc.)


Comes on DTC stored

MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.

When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.

NOTICE:

If driving continues under these conditions, clutches will burn out and the vehicle will no longer be drivable.


CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


PROCEDURE

1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P2714)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P2714 is output A
P2714 and other DTCs are output B


HINT:

If shift solenoid valve SLT is stuck on, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.




A

4.INSPECT SHIFT SOLENOID VALVE SLT

B

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)
2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test while the ATF temperature is 50 to 80°C (122 to 176°F).

·

Be careful to prevent the hose of SST from interfering with the exhaust pipe.

·

This check must be conducted after checking and confirming that the engine is normal.

·

Perform the test with the A/C off.



HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C226143E02
2.417,0.604 2.531,0.417 false 0.604,1.844 0.719,1.656 false 2.563,0.323 3.021,0.521 0.458,0.198 10 SST 0.313,1.771 0.771,1.969 0.458,0.198 10 SST

Remove the test plug from the transaxle case and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

b.

Connect the GTS to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure when the engine is idling.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.


h.

Measure the line pressure with SST.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:

ON: No action (normal operation)

OFF: Line pressure up (When Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT to turn off).


[Vehicle Condition]
·

Vehicle stopped

·

Engine idling


Powertrain > Engine and ECT > Active Test
Tester Display
Activate the Solenoid (SLT)
50004 234 130
HINT:

Activate the Solenoid (SLT) in the Active Test is performed to confirm that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST

Note that the pressure readings for the Active Test and Hydraulic Test are different.


OK:

The line pressure changes as specified when performing the Active Test.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (DRIVING TEST)

NG

4.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING GTS (DRIVING TEST)
NOTICE:

This test should always be performed with at least 2 people.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

HINT:
·

Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

·

The gear commanded by the ECM is shown in the Data List / Shift Status display on the GTS.



Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Shift Position Operate the shift solenoid valves and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Can be used to check the operation of the shift solenoid valves.
A 10-second interval is required between gear changes.
Do not down-shift at high speeds. Doing so will damage the automatic transaxle.
[Vehicle Condition]
50 km/h (30 mph) or less
Powertrain > Engine and ECT > Active Test
Active Test Display
Control the Shift Position
Data List Display
Shift Status
50004 234 116 416
NOTICE:
·

This test can be conducted when the vehicle is stopped.

·

When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.




h.

Check the vehicle speed and the gear when the engine speed is 1000 rpm.

HINT:

Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th, and 6th gear, however a difference of speed should still be evident following each gear change.


Standard:
1st 2nd 3rd 4th 5th 6th
8 to 12 km/h (5 to 7.5 mph) 15 to 19 km/h (9.3 to 11.8 mph) 21 to 25 km/h (13.0 to 15.5 mph) 31 to 35 km/h (19.3 to 21.7 mph) 44 to 48 km/h (27.3 to 29.8 mph) 52 to 56 km/h (32.3 to 34.8 mph)



i.

Compare the ECM commanded gear and the actual gear.

Result:
System Condition ECM Gear Shift Command Proceed to
1st 2nd 3rd 4th 5th 6th
Malfunction Shift solenoid valve SL1 Stuck ON 1st 2nd 3rd 4th 4th 4th A
Shift solenoid valve SL1 Stuck OFF N*1 N*1 N*1 N*1 5th 6th
Shift solenoid valve SL2 Stuck ON 4th 4th 4th 4th 5th 6th B
Shift solenoid valve SL2 Stuck OFF 1st 2nd 3rd 1st N*1 N*1
Shift solenoid valve SL3 Stuck ON 2nd 2nd 3rd 4th 5th 6th C
Shift solenoid valve SL3 Stuck OFF 1st 1st 3rd 4th 5th N*1
Shift solenoid valve SL4 Stuck ON*3 3rd 3rd 3rd 4th 5th 5th D
Shift solenoid valve SL4 Stuck OFF 1st 2nd 1st 4th N*1 6th
Shift solenoid valve SLT Stuck ON N*2 N*2 N*2 N*2 N*2 N*2 E
Shift solenoid valve SLT Stuck OFF*3 1st 2nd 3rd 4th 5th 6th


HINT:
·

*1: Neutral

·

*2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is less than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.

·

*3: When shift solenoid valve SLT is stuck off, gear shifting is normal.





A

B

C

D

E

4.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE SLT
a.
C197715C14
1.781,0.969 2.167,0.427 true 1.781,2.948 2.167,2.406 true 1.469,0.969 1.083,0.417 true 1.469,2.948 1.083,2.396 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 2.198,0.323 2.375,0.542 0.177,0.219 10 false 1 2.198,2.302 2.375,2.521 0.177,0.219 10 false 1 0.969,0.323 1.146,0.542 0.177,0.219 10 false 2 0.969,2.313 1.146,2.531 0.177,0.219 10 false 2 1.854,3.938 2.313,4.135 0.458,0.198 10 false (+) 1.271,3.938 1.729,4.135 0.458,0.198 10 false (-)
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY