Home › Drivetrain › U760E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008752 U760E AUTOMATIC TRANSMISSION / TRANSAXLE _0061120 AUTOMATIC TRANSAXLE SYSTEM C

U760E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0798  Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3)  


DESCRIPTION

Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) An open or short circuit (output signal duty is 0% or 100%) is detected by the ECM in the shift solenoid valve SL3 circuit while driving and shifting gears (SL3 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).
·

Open or short in shift solenoid valve SL3 circuit

·

Shift solenoid valve SL3

·

Wiring harness connector

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. And the ECM performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the ECM stops sending current to the circuit.)

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART

WIRING DIAGRAM

C239277E23
5.667,4.396 6.094,4.583 0.427,0.188 10 false ECM 5.083,1.26 5.51,1.448 0.427,0.188 10 false SL3+ 5.083,2.646 5.51,2.833 0.427,0.188 10 false SL3- 3.625,1.26 4.052,1.448 0.427,0.188 10 false SL3+ 3.625,2.646 4.052,2.833 0.427,0.188 10 false SL3- 1.625,1.969 2.604,2.302 0.979,0.333 10 false Shift Solenoid Valve SL3 1.083,3.49 2.646,3.677 1.563,0.188 10 false Transmission Wire 3.031,3.479 4.031,3.833 1,0.354 10 false Wiring Harness Connector 3.115,1.26 3.542,1.448 0.427,0.188 10 false SL3+ 3.115,2.646 3.542,2.833 0.427,0.188 10 false SL3- 2.313,1.26 2.74,1.448 0.427,0.188 10 false SL3+ 2.313,2.646 2.74,2.833 0.427,0.188 10 false SL3- 5.667,4.229 6.021,4.385 0.354,0.156 10 false B77 4.813,1.531 5.083,1.688 0.271,0.156 10 false 11 4.813,2.927 5.083,3.083 0.271,0.156 10 false 10 2.802,2.563 3.094,2.719 0.292,0.156 10 false 15 4.063,1.167 4.354,1.333 0.292,0.167 10 false 19 4.063,2.563 4.344,2.729 0.281,0.167 10 false 18 4.01,2.76 4.292,2.917 0.281,0.156 10 false B78 4.01,1.365 4.292,1.521 0.281,0.156 10 false B78 2.833,2.76 3.167,2.917 0.333,0.156 10 false A 2.833,1.375 3.188,1.531 0.354,0.156 10 false A 2.792,1.177 3.073,1.333 0.281,0.156 10 false 16 1.406,1.708 1.833,1.896 0.427,0.188 10 false 1 1.406,2.365 1.833,2.552 0.427,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

The following table shows normal operation of the shift solenoid valve SL3 when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL3 OFF ON OFF OFF OFF ON


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL3 CIRCUIT)
a.
C267934C04
1.448,0.177 1.865,0.385 0.417,0.208 0.688,1.719 0.99,0.885 true 1.51,1.708 1.052,0.885 true 1.531,0.208 1.99,0.406 0.458,0.198 10 false B77 0.417,1.75 1.125,1.969 0.708,0.219 10 false 10 (SL3-) 1.26,1.75 1.979,1.969 0.719,0.219 10 false 11 (SL3+) 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B77-11 (SL3+) - B77-10 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
B77-11 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
B77-10 (SL3-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
2.CHECK HARNESS AND CONNECTOR (WIRING HARNESS CONNECTOR - ECM)
a.

Disconnect the B78 wiring harness connector.


b.

Disconnect the B77 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B78-19 (SL3+) - B77-11 (SL3+) Always Below 1 Ω
B78-18 (SL3-) - B77-10 (SL3-) Always Below 1 Ω
B78-19 (SL3+) or B77-11 (SL3+) - Body ground and other terminals Always 10 kΩ or higher
B78-18 (SL3-) or B77-10 (SL3-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL3)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL3)
a.
C226545C05
0.594,0.76 0.938,1 0.344,0.24 1.75,1.5 1.552,0.969 true 1.313,1.51 1.427,0.969 true 0.354,0.219 0.667,0.417 0.313,0.198 10 *a 1.635,1.552 2.25,1.75 0.615,0.198 10 SL3- 0.708,0.792 1.063,0.99 0.354,0.198 10 A 1.156,1.552 1.771,1.75 0.615,0.198 10 SL3+
*a Component without harness connected
(Transmission Wire)


Remove the wiring harness connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (SL3+) - A-15 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
A-16 (SL3+) - Body ground Always 10 kΩ or higher
A-15 (SL3-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT SHIFT SOLENOID VALVE SL3
4.INSPECT SHIFT SOLENOID VALVE SL3
a.
C197715C15
1.781,0.969 2.167,0.427 true 1.781,2.948 2.167,2.406 true 1.469,0.969 1.083,0.417 true 1.469,2.948 1.083,2.396 true 0.104,0.104 0.417,0.302 0.313,0.198 10 *1 2.198,0.323 2.375,0.542 0.177,0.219 10 1 2.198,2.302 2.375,2.521 0.177,0.219 10 1 0.969,0.323 1.146,0.542 0.177,0.219 10 2 0.969,2.313 1.146,2.531 0.177,0.219 10 2 1.854,3.938 2.313,4.135 0.458,0.198 10 (+) 1.271,3.938 1.729,4.135 0.458,0.198 10 (-)
*1 Shift Solenoid Valve SL3


Remove shift solenoid valve SL3.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG