Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0062871 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  One or more Power Seat Motors do not Operate  


DESCRIPTION

Signals are input into the position control ECU and switch assembly. The built-in ECU manages the signals received from the front power seat switch assembly and operates each motor. If the position control ECU and switch assembly receives more than 2 motor operation signals, the motor is stopped. Manual operation is restarted after the position control ECU and switch assembly receives 1 signal only.

WIRING DIAGRAM

B342190
5.5,0.74 6.375,0.979 0.875,0.24 10 false from Battery 4.052,0.99 5.031,1.177 0.979,0.188 10 false ECU-B NO. 1 1.083,6.021 2.448,6.385 1.365,0.365 10 false Position Control ECU and Switch Assembly 2.438,0.75 2.896,0.948 0.458,0.198 10 false e6 2.438,0.552 2.75,0.75 0.313,0.198 10 false 12 2.406,1.75 2.865,1.948 0.458,0.198 10 false e18 2.406,2.146 2.865,2.344 0.458,0.198 10 false e18 2.417,3.177 2.875,3.375 0.458,0.198 10 false e18 2.406,3.583 2.865,3.781 0.458,0.198 10 false e18 2.417,4.625 2.875,4.823 0.458,0.198 10 false e18 2.417,5.031 2.875,5.229 0.458,0.198 10 false e18 4.927,2.406 5.385,2.604 0.458,0.198 10 false e12 4.917,3.833 5.375,4.031 0.458,0.198 10 false e13 4.938,5.281 5.396,5.479 0.458,0.198 10 false e14 4.938,2.583 5.813,2.802 0.875,0.219 10 false Slide Motor 4.906,4.021 6.219,4.25 1.313,0.229 10 false Front Vertical Motor 4.958,5.458 5.781,5.646 0.823,0.188 10 false Lifter Motor 4.667,5.969 6.26,6.385 1.594,0.417 10 false Separate Type Front Seat Cushion Spring Assembly 1.875,0.74 2.49,0.938 0.615,0.198 10 false SYSB 1.917,1.76 2.531,1.958 0.615,0.198 10 false SLD+ 1.948,2.167 2.563,2.365 0.615,0.198 10 false SLD- 1.896,3.177 2.51,3.375 0.615,0.198 10 false FRV+ 1.938,3.573 2.552,3.771 0.615,0.198 10 false FRV- 1.948,4.635 2.563,4.833 0.615,0.198 10 false LFT+ 1.969,5.042 2.583,5.24 0.615,0.198 10 false LFT- 2.479,1.531 2.635,1.729 0.156,0.198 10 false 3 2.49,1.948 2.646,2.146 0.156,0.198 10 false 4 2.49,2.969 2.646,3.167 0.156,0.198 10 false 8 2.49,3.385 2.646,3.583 0.156,0.198 10 false 5 2.438,4.417 2.75,4.615 0.313,0.198 10 false 10 2.448,4.833 2.76,5.031 0.313,0.198 10 false 12 4.76,1.635 4.917,1.833 0.156,0.198 10 false 4 4.76,2.031 4.917,2.229 0.156,0.198 10 false 1 4.76,3.063 4.917,3.26 0.156,0.198 10 false 4 4.771,3.469 4.927,3.667 0.156,0.198 10 false 1 4.76,4.521 4.917,4.719 0.156,0.198 10 false 4 4.75,4.917 4.906,5.115 0.156,0.198 10 false 1

B342191
5,1.49 6.083,1.708 1.083,0.219 10 false Reclining Motor 4.99,1.313 5.302,1.51 0.313,0.198 10 false f1 4.781,0.552 4.938,0.75 0.156,0.198 10 false 4 4.771,0.958 4.927,1.156 0.156,0.198 10 false 1 2.417,1.073 2.875,1.271 0.458,0.198 10 false e18 2.406,0.667 2.865,0.865 0.458,0.198 10 false e18 0.865,0.677 1.323,0.875 0.458,0.198 10 false e18 0.865,1.083 1.323,1.281 0.458,0.198 10 false e18 1.917,0.677 2.531,0.875 0.615,0.198 10 false RCL+ 1.938,1.073 2.552,1.271 0.615,0.198 10 false RCL- 2.479,0.458 2.635,0.656 0.156,0.198 10 false 9 2.448,0.875 2.76,1.073 0.313,0.198 10 false 11 4.719,2.01 6.313,2.448 1.594,0.438 10 false Separate Type Front Seat Cushion Spring Assembly 1.25,0.677 1.708,0.875 0.458,0.198 10 false +B2 1.229,1.094 1.844,1.292 0.615,0.198 10 false GND2 0.938,0.469 1.094,0.667 0.156,0.198 10 false 6 0.927,0.896 1.083,1.094 0.156,0.198 10 false 1 0.833,5.323 1.292,5.521 0.458,0.198 10 false e19 4.74,4.688 5.052,4.885 0.313,0.198 10 false f3 4.521,5.656 6.375,6.073 1.854,0.417 10 false Separate Type Front Seatback Spring Assembly 1.073,2.188 2.427,2.573 1.354,0.385 10 false Position Control ECU and Switch Assembly 0.823,5.51 2.698,5.729 1.875,0.219 10 false Power Seat Switch Assembly 1.031,4.01 1.188,4.208 0.156,0.198 10 false 2 1.021,4.406 1.177,4.604 0.156,0.198 10 false 5 2.375,3.885 2.531,4.083 0.156,0.198 10 false 1 2.385,4.333 2.542,4.531 0.156,0.198 10 false 3 4.771,3.885 4.927,4.083 0.156,0.198 10 false 2 4.771,4.333 4.927,4.531 0.156,0.198 10 false 1 4.75,4.833 6.292,5.188 1.542,0.354 10 false Lumbar Support Adjuster Assembly 1.208,4.021 1.365,4.219 0.156,0.198 10 false E 1.208,4.417 1.365,4.615 0.156,0.198 10 false B 2.188,3.896 2.344,4.094 0.156,0.198 10 false R 2.198,4.313 2.354,4.51 0.156,0.198 10 false H

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switch assembly.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


Result:
Result Proceed to
One or more power seat functions (except lumbar support adjustment function) do not operate A
All power seat functions do not operate B
Front vertical and lifter functions do not operate C
Only lumbar support adjustment function does not operate D



A

2.READ VALUE USING GTS (POWER SEAT SWITCH)

B

GO TO OTHER DIAGNOSIS PROCEDURE (Front Power Seat does not Operate with Front Power Seat Switch)

C

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)

D

8.INSPECT POWER SEAT SWITCH ASSEMBLY
2.READ VALUE USING GTS (POWER SEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reclining Rear Reclining switch signal (Rearward) ON or OFF ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front Reclining switch signal (Forward) ON or OFF ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down Front vertical switch signal (Downward) ON or OFF ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up Front vertical switch signal (Upward) ON or OFF ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down Lifter switch signal (Downward) ON or OFF ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up Lifter switch signal (Upward) ON or OFF ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear Slide switch signal (Rearward) ON or OFF ON: Slide switch (Rearward) on
OFF: Slide switch (Rearward) off
-
Slide Front Slide switch signal (Forward) ON or OFF ON: Slide switch (Forward) on
OFF: Slide switch (Forward) off
-
Body Electrical > Driver Seat > Data List
Tester Display
Reclining Rear
Reclining Front
Front Vertical Down
Front Vertical Up
Lifter Switch Down
Lifter Switch Up
Slide Rear
Slide Front
50003 162 17,18,19,20,21,22,23,24
OK:

ON or OFF is displayed on the GTS according to the table above.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR)
a.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Seat Reclining Seat reclining operation OFF/Rear/Front -
Front Vertical Operation Seat front vertical operation OFF/Down/Up -
Lifter Operation Seat lifter operation OFF/Down/Up -
Seat Slide Operation Seat slide operation OFF/Rear/Front -
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Reclining
50004 162 1
Body Electrical > Driver Seat > Active Test
Tester Display
Front Vertical Operation
50004 162 3
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
Body Electrical > Driver Seat > Active Test
Tester Display
Seat Slide Operation
50004 162 4
Result:
Result Proceed to
The power seat functions operate normally. A
Slide, front vertical or lifter function does not operate normally. B
Reclining function does not operate normally. C




A

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

C

5.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Remove the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seat cushion spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

5.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
a.

Remove the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT MOTOR)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the wire harness and connector between the position control ECU and switch assembly and the applicable motor.


Standard Resistance:
Tester Connection Condition Specified Condition
e18-3 (SLD+) - e12-4 Always Below 1 Ω
e18-4 (SLD-) - e12-1 Always Below 1 Ω
e18-5 (FRV-) - e13-1 Always Below 1 Ω
e18-8 (FRV+) - e13-4 Always Below 1 Ω
e18-10 (LFT+) - e14-4 Always Below 1 Ω
e18-12 (LFT-) - e14-1 Always Below 1 Ω
e18-9 (RCL+) - f1-4 Always Below 1 Ω
e18-11 (RCL-) - f1-1 Always Below 1 Ω
e18-3 (SLD+) - Body ground Always 10 kΩ or higher
e18-4 (SLD-) - Body ground Always 10 kΩ or higher
e18-5 (FRV-) - Body ground Always 10 kΩ or higher
e18-8 (FRV+) - Body ground Always 10 kΩ or higher
e18-10 (LFT+) - Body ground Always 10 kΩ or higher
e18-12 (LFT-) - Body ground Always 10 kΩ or higher
e18-9 (RCL+) - Body ground Always 10 kΩ or higher
e18-11 (RCL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the e6 position control ECU and switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e6-12 (SYSB) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT POWER SEAT SWITCH ASSEMBLY
a.

Remove the power seat switch assembly.

Click hereVehicle Interior>SEAT>LUMBAR SWITCH>REMOVAL


b.

Inspect the power seat switch assembly.

Click hereVehicle Interior>SEAT>LUMBAR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

NG

REPLACE POWER SEAT SWITCH ASSEMBLY

9.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
a.

Remove the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY


b.

Inspect the separate type front seatback spring assembly.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT SWITCH ASSEMBLY AND LUMBAR MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH ASSEMBLY - POWER SEAT SWITCH ASSEMBLY AND LUMBAR MOTOR)
a.

Disconnect the e18 position control ECU and switch assembly connector.


b.

Disconnect the e19 power seat switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e18-6 (+B2) - e19-5 (B) Always Below 1 Ω
e18-1 (GND2) - e19-2 (E) Always Below 1 Ω
e19-3 (H) - f3-1 Always Below 1 Ω
e19-1 (R) - f3-2 Always Below 1 Ω
e19-5 (B) - Body ground Always 10 kΩ or higher
e19-2 (E) - Body ground Always 10 kΩ or higher
e19-3 (H) - Body ground Always 10 kΩ or higher
e19-1 (R) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR