Home › Drivetrain › EA64F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT
RM3090E _52 Drivetrain _008756 EA64F MANUAL TRANSMISSION / TRANSAXLE _0048561 MANUAL TRANSAXLE UNIT A

EA64F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 31204 1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 3.REMOVE RELEASE FORK SUPPORT

Hide 31126 4.REMOVE CLUTCH RELEASE FORK BOOT

a.
C113599

Remove the clutch release fork boot from the front transaxle assembly.


Hide 33524B 5.REMOVE CONTROL CABLE BRACKET

a.
C115444

Remove the 3 bolts and cable bracket from the manual transaxle assembly.


Hide 33590F 6.REMOVE FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY

a.
C112480

Remove the 2 bolts and floor shift selecting bell crank assembly from the manual transaxle assembly.


Hide 84210 7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C112471N03
0.273,0.826 0.576,1.15 0.302,0.323 10 SST 0.626,0.89 0.845,0.89 0.845,0.89 1.578,1.079 false

Using SST, remove the back-up light switch assembly and gasket.

SST
09817-16011  


Hide 33101Q 8.REMOVE NO. 1 TRANSMISSION CASE PLUG

a.
C278088

Using a T55 ''TORX'' socket wrench, remove the No. 1 transmission case plug.


Hide 33290 9.REMOVE NO. 1 LOCK BALL ASSEMBLY

a.
C116559

Remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33290B 10.REMOVE NO. 2 LOCK BALL ASSEMBLY

a.
C116599

Remove the No. 2 lock ball assembly from the manual transmission case.


Hide 33295B 11.REMOVE SHIFT GATE PIN

a.
C116598

Remove the shift gate pin from the manual transmission case.


Hide 33251A 12.REMOVE SHIFT AND SELECT LEVER ASSEMBLY

a.
C112484

Remove the 4 bolts and shift and select lever assembly from the manual transmission assembly.


Hide 33261F 13.REMOVE SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN

a.
C277747N01
1,0.917 1.271,1.104 0.271,0.188 10 (A) 1.385,1.344 1.635,1.542 0.25,0.198 10 (B)

While pressing in the shift and select lever shaft straight pin (A) as far as it will go, pull out the shift and select lever shaft straight pin (B) to remove it.


b.

Remove the spring.


Hide 33403L 14.REMOVE O-RING

a.
C277749

Remove the O-ring from the shift and select lever shaft straight pin (B).


Hide 33101A 15.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C113635

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 16.REMOVE DRAIN PLUG

a.
C113634

Remove the drain plug and gasket from the front transaxle case.


Hide 33275C 17.REMOVE SHIFT DETENT BALL

a.
C113593

Using a 6 mm hexagon wrench, remove the 4 detent ball plugs from the front transaxle case.


b.

Using a magnet hand, remove the 4 No. 1 shift detent ball spring seats, 4 shift detent ball compression springs and 4 shift detent balls.


Hide 18.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C116545

Remove the reverse idler gear shaft bolt and gasket from the manual transmission case.


Hide 33111A 19.REMOVE MANUAL TRANSMISSION CASE PLUG

a.
C277754

Remove the 2 manual transmission case plugs from the manual transmission case.


Hide 33111 20.REMOVE MANUAL TRANSMISSION CASE

a.
C113600

Remove the 6 bolts from the front transaxle case.


b.
C113610

Remove the 12 bolts from the manual transmission case.


c.
C116542

Using 2 pairs of snap ring pliers to keep the snap ring stretched, remove the manual transmission case.


Hide 33124C 21.REMOVE NO. 1 OIL RECEIVER PIPE

a.
C113590

Remove the No. 1 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33176B 22.REMOVE TRANSMISSION OIL SEPARATOR

a.
C277755

for Manual Transmission Case Side:

Remove the 2 bolts and transmission oil separator from the manual transmission case.


Hide 33242F 23.REMOVE 1ST AND 2ND SHIFT FORK SHAFT

a.
C115434

Remove the bolt from the No. 1 gear shift fork.


b.
C116327

Remove the 1st and 2nd shift fork shaft.


Hide 33243F 24.REMOVE 3RD AND 4TH SHIFT FORK SHAFT

a.
C117839

Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift head.


b.
C117840

Using a 5 mm pin punch and hammer, tap out the pin from the No. 2 gear shift fork.


c.
C115438C04
2.26,0.823 1.344,0.125 1.344,0.125 0.875,0.125 false 2.302,1.781 2.875,1.188 2.875,1.188 3,1.188 false 0.667,0.042 0.948,0.25 0.281,0.208 10 *1 3.052,1.104 3.354,1.313 0.302,0.208 10 *2
*1 3rd and 4th Shift Fork Shaft
*2 No. 2 Gear Shift Head


Remove the 3rd and 4th shift fork shaft and No. 2 gear shift head.


Hide 33213G 25.REMOVE NO. 2 GEAR SHIFT FORK

a.
C115439

Remove the No. 2 gear shift fork from the No. 1 output shaft assembly.


Hide 33246C 26.REMOVE NO. 5 GEAR SHIFT FORK SHAFT

a.
C115440

Using a screwdriver, remove the E-ring from the pin.


b.
C115441

Remove the pin from the shift arm.


c.
C115442

Remove the No. 5 gear shift fork shaft from the front transaxle case.


d.
C113585

Using a 5 mm pin punch and hammer, tap out the pin.


e.

Remove the No. 3 gear shift head from the No. 5 gear shift fork shaft.


Hide 33212A 27.REMOVE NO. 1 GEAR SHIFT FORK

a.
C115443

Remove the No. 1 gear shift fork from the No. 1 output shaft assembly.


Hide 33222F 28.REMOVE SHIFT ARM

a.
C116744

Remove the shift arm from the front transaxle case.


Hide 33245H 29.REMOVE REVERSE SHIFT FORK SHAFT

a.
C115428

Remove the bolt from the reverse shift fork.


b.
C115429

Remove the reverse shift fork shaft from the front transaxle case.


Hide 33244J 30.REMOVE 5TH AND 6TH SHIFT FORK SHAFT

a.
C115430

Remove the bolt from the No. 3 gear shift fork.


b.
C115431

Remove the 5th and 6th shift fork shaft from the front transaxle case.


Hide 33214G 31.REMOVE NO. 3 GEAR SHIFT FORK

a.
C277715

Remove the No. 3 gear shift fork from the No. 2 output shaft assembly.


Hide 33211 32.REMOVE REVERSE SHIFT FORK

a.
C115432

Remove the reverse shift fork from the No. 2 output shaft assembly.


Hide 33.INSPECT REVERSE IDLER GEAR THRUST CLEARANCE

Hide 34.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

Hide 33461 35.REMOVE REVERSE IDLER GEAR

a.
C278117

Remove the reverse idler gear shaft by sliding and lifting it.


b.
C277716

Remove the reverse idler gear, needle roller bearing and reverse idler thrust washer from the reverse idler gear shaft.


Hide 33311 36.REMOVE INPUT SHAFT, NO. 1 OUTPUT SHAFT ASSEMBLY AND NO. 2 OUTPUT SHAFT ASSEMBLY

a.
C116196

Remove the 3 shafts at the same time.

NOTICE:

Do not drop the input shaft, No. 1 output shaft assembly and No. 2 output shaft assembly.



Hide 33176B 37.REMOVE TRANSMISSION OIL SEPARATOR

a.
C277758

for Front Transaxle Case Side:

Remove the 2 bolts and transmission oil separator from the front transaxle case.


Hide 41301L 38.REMOVE FRONT DIFFERENTIAL CASE ASSEMBLY

a.
C115412

Remove the front differential case assembly from the front transaxle case.


Hide 33449 39.REMOVE TRANSMISSION MAGNET

a.
C115449

Remove the transmission magnet from the front transaxle case.


Hide 33322A 40.REMOVE REAR NO. 2 OUTPUT SHAFT BEARING OUTER RACE

a.
C277774C01
1.646,0.469 1.875,0.135 1.875,0.135 2.208,0.135 false 2.729,0.635 2.948,0.833 0.219,0.198 10 *a 0.313,0.344 0.552,0.521 0.24,0.177 10 *b 2.271,0.052 2.729,0.25 0.458,0.198 10 SST
*a Turn
*b Hold


Using SST, remove the rear No. 2 output shaft bearing outer race the manual transmission case to remove it.

SST
09387-00041  (09387-02020)


Hide 33321H 41.REMOVE REAR OUTPUT SHAFT BEARING SHIM

a.
C116565

Remove the rear output shaft bearing shim from the manual transmission case.


Hide 33242L 42.REMOVE SHIFT FORK SHAFT BEARING

a.
C113594N01
0.406,1.125 0.281,2.208 0.281,2.208 1,1.552 false 0.281,2.208 0.885,1.052 false 0.104,2.281 0.417,2.646 0.313,0.365 10 SST

Using SST, remove the 4 shift fork shaft bearings from the manual transmission case to remove them.

SST
09387-00041  (09387-01021, 09387-01030)
09527-20011  
09612-65014  


Hide 33261K 43.REMOVE SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING

a.
C113581N02
0.077,0.412 0.387,0.758 0.31,0.347 10 SST 1.095,1.607 0.457,0.497 0.457,0.497 1.009,0.648 false

Using SST, remove the shift and select lever shaft needle roller bearing from the manual transmission case to remove it.

SST
09387-00041  (09387-01021, 09387-01030)
09612-65014  


Hide 33311P 44.REMOVE REAR INPUT AND OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C116544

Using a snap ring expander, remove the rear input and output shaft bearing shaft snap rings.


Hide 33311A 45.REMOVE FRONT INPUT SHAFT BEARING

a.
C278098

Remove the bolt and bearing lock plate from the front transaxle case.


b.
C277775C01
0.677,1.646 1.031,1.646 false 2.708,1.531 2.948,1.698 0.24,0.167 10 *a 0.146,0.667 0.396,0.854 0.25,0.188 10 *b 0.365,1.563 0.729,1.74 0.365,0.177 10 SST
*a Turn
*b Hold


Using SST, remove the front input shaft bearing from the front transaxle case to remove it.

SST
09612-30012  


Hide 31105H 46.REMOVE TRANSAXLE CASE OIL SEAL

a.
C279708C01
0.771,1.813 1.021,1.813 1.021,1.813 1.521,1.458 false 0.406,1.719 0.719,1.917 0.313,0.198 10 *a
*a Protective Tape


Using a screwdriver, remove the transaxle case oil seal from the front transaxle case.

NOTICE:

Do not damage the installation surface of the front transmission case.


HINT:

Tape the screwdriver tip before use.



Hide 33321N 47.REMOVE FRONT OUTPUT SHAFT BEARING

a.
C278099

Remove the bolt and bearing lock plate from the front transaxle case.


b.
C279717C01
0.333,1.333 0.333,1.167 0.333,1.167 1.083,1.167 false 0.25,1.417 0.646,1.656 0.396,0.24 10 SST 0.115,0.51 0.344,0.719 0.229,0.208 10 *a 1.656,0.323 1.865,0.51 0.208,0.188 10 *b
*a Turn
*b Hold


Using SST, remove the front output shaft bearing from the front transaxle case to remove it.

SST
09612-65014  (09612-01020)


Hide 33134B 48.REMOVE OUTPUT SHAFT COVER

a.
C115453

Remove the output shaft cover from the front transaxle case.


Hide 33322B 49.REMOVE FRONT NO. 2 OUTPUT SHAFT BEARING OUTER RACE

a.
C277777C01
2.49,0.177 2.271,0.177 2.271,0.177 2.031,0.823 false 2.781,1.219 2.979,1.406 0.198,0.188 10 *a 1.01,0.49 1.229,0.708 0.219,0.219 10 *b 2.542,0.104 3,0.302 0.458,0.198 10 SST
*a Turn
*b Hold


Using SST, remove the front No. 2 output shaft bearing outer race from the front transaxle case to remove it.

SST
09387-00041  (09387-02020)


Hide 33134B 50.REMOVE OUTPUT SHAFT COVER

a.
C115454

Remove the output shaft cover from the front transaxle case.


Hide 33111J 51.REMOVE MANUAL TRANSMISSION CASE STRAIGHT PIN

a.
C278092

Remove the 4 manual transmission case straight pin.


Hide 33242L 52.REMOVE SHIFT FORK SHAFT BEARING

a.
C113595N02
0.479,0.781 0.25,0.938 0.25,0.938 0.24,2.396 false 0.094,2.458 0.479,2.656 0.385,0.198 10 SST

Using SST, remove the 4 shift fork shaft bearings from the front transaxle case to remove them.

SST
09387-00041  (09387-01021)
09612-65014  


Hide 41311F 54.REMOVE FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING

a.
C116548

Using a brass bar and hammer, tap out the front differential case rear outer race bearing and front differential case rear shim from the manual transmission case.


Hide 41311E 56.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C326346N02
1.813,3.094 2.271,2.74 2.271,2.74 2.49,2.74 true 2.073,2.125 2.531,1.771 2.531,1.771 2.75,1.771 true 2.823,1.698 3.281,1.896 0.458,0.198 10 false SST 2.615,2.677 3.073,2.875 0.458,0.198 10 false SST

Using SST, remove the front differential case frontbearing outer race from the front transaxle case.

SST
09950-40011  (09951-04010, 09953-04030, 09954-04010, 09955-04041, 09957-04010)
09950-60010  (09951-00600)