Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066372 AIRBAG SYSTEM(w/ Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ Occupant Classification System)  B1830/57  Short in Curtain Shield Squib RH Circuit  B1831/57  Open in Curtain Shield Squib RH Circuit  B1832/57  Short to GND in Curtain Shield Squib RH Circuit  B1833/57  Short to B+ in Curtain Shield Squib RH Circuit  


DESCRIPTION

The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1830/57 Short in Curtain Shield Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.

·

A curtain shield squib RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag sensor assembly


B1831/57 Open in Curtain Shield Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the curtain shield squib RH circuit for 2 seconds.

·

A curtain shield squib RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag sensor assembly


B1832/57 Short to GND in Curtain Shield Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag sensor assembly


B1833/57 Short to B+ in Curtain Shield Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.

·

A curtain shield squib RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag sensor assembly



WIRING DIAGRAM

C253326E56
2.031,1.563 2.646,1.76 0.615,0.198 10 false ICR+ 2.469,1.563 3.083,1.76 0.615,0.198 10 false 1 2.042,2.406 2.656,2.604 0.615,0.198 10 false ICR- 2.469,2.406 3.083,2.604 0.615,0.198 10 false 2 0.74,3.042 1.354,3.24 0.615,0.198 10 false M9 0.74,3.219 2.958,3.604 2.219,0.385 10 false Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) 4.76,1.677 5.375,1.875 0.615,0.198 10 false ICR+ 4.76,2.521 5.375,2.719 0.615,0.198 10 false ICR- 4.563,1.563 4.76,1.781 0.198,0.219 10 false 4 4.563,2.417 4.76,2.615 0.198,0.198 10 false 3 4.792,4.167 5.406,4.365 0.615,0.198 10 false M25 4.792,4.344 6.479,4.552 1.688,0.208 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)
a.
C252994C02
0.396,2.208 0.74,2.438 0.344,0.229 2.063,2.542 2.323,2.813 false 0.885,0.302 1.198,0.458 0.313,0.156 10 false *1 2.135,1.375 2.448,1.531 0.313,0.156 10 false *2 2.302,2.24 2.615,2.396 0.313,0.156 10 false *3 1.625,1.646 1.938,1.802 0.313,0.156 10 false *a 2.229,2.844 2.677,3.031 0.448,0.188 10 false *4 1.833,0.49 2.146,0.646 0.313,0.156 10 false A 1.313,0.76 1.625,0.917 0.313,0.156 10 false C 1.083,0.76 1.396,0.917 0.313,0.156 10 false D 0.458,2.24 0.771,2.396 0.313,0.156 10 false M9
*1 Curtain Shield Squib RH
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib RH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the curtain shield airbag assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.


Result:
Proceed to
DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output
DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output



DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output

DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208249C02
0.852,0.944 1.045,1.183 0.193,0.24 10 D 0.647,0.456 0.84,0.624 0.193,0.168 10 *1 1.252,0.448 1.446,0.615 0.193,0.168 10 *2 1.698,1.671 1.892,1.838 0.193,0.168 10 *3 1.084,0.944 1.296,1.165 0.212,0.221 10 C 1.497,0.944 1.709,1.174 0.212,0.23 10 B 1.902,0.651 2.095,0.835 0.193,0.184 10 A
*1 Curtain Shield Squib RH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and curtain shield airbag assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK CURTAIN SHIELD SQUIB RH CIRCUIT

NG

REPLACE FLOOR WIRE

3.CHECK CURTAIN SHIELD SQUIB RH CIRCUIT
a.
C252995C01
0.25,2.042 0.552,2.271 0.302,0.229 1.104,2.75 1.542,2.396 false 2.26,2.74 1.76,2.396 false 0.896,0.281 1.208,0.438 0.313,0.156 10 false *1 1.458,0.302 1.771,0.458 0.313,0.156 10 false *2 2.333,1.354 2.646,1.51 0.313,0.156 10 false *3 2.25,2.073 2.563,2.229 0.313,0.156 10 false *4 1.573,1.75 1.885,1.906 0.313,0.156 10 false *a 2.042,0.458 2.354,0.615 0.313,0.156 10 false A 1.719,0.781 2.031,0.938 0.313,0.156 10 false B 1.302,0.781 1.615,0.938 0.313,0.156 10 false C 1.083,0.781 1.396,0.938 0.313,0.156 10 false D 2.313,2.688 2.729,2.885 0.417,0.198 10 false ICR- 0.75,2.677 1.167,2.875 0.417,0.198 10 false ICR+ 0.302,2.073 0.719,2.271 0.417,0.198 10 false M9
*1 Curtain Shield Squib RH
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M9-1 (ICR+) - Body ground Ignition switch ON Below 1 V
M9-2 (ICR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-1 (ICR+) - M9-2 (ICR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-1 (ICR+) - M9-2 (ICR-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-1 (ICR+) - Body ground Always 1 MΩ or higher
M9-2 (ICR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C146259C09
0.729,0.25 0.958,0.406 0.229,0.156 10 false *1 1.896,1.354 2.073,1.531 0.177,0.177 10 false *2 1,0.656 1.135,0.823 0.135,0.167 10 false D 1.135,0.656 1.271,0.823 0.135,0.167 10 false C 1.677,0.438 1.813,0.604 0.135,0.167 10 false A
*1 Curtain Shield Squib RH
*2 Airbag Sensor Assembly


Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.



Result:
Proceed to
DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output
DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output



DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output

DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output