The variable vent hole squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly. The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are stored when a malfunction is detected in the variable vent hole squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B181A/7A | Short in Passenger Side Airbag Variable Vent Hole Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the variable vent hole squib circuit during the primary check. ·
A variable vent hole squib malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 2 instrument panel wire ·
Instrument panel wire ·
Instrument panel passenger airbag assembly (Variable vent hole squib) ·
Airbag sensor assembly |
| B181B/7A | Open in Passenger Side Airbag Variable Vent Hole Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the variable vent hole squib circuit for 2 seconds. ·
A variable vent hole squib malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 2 instrument panel wire ·
Instrument panel wire ·
Instrument panel passenger airbag assembly (Variable vent hole squib) ·
Airbag sensor assembly |
| B181C/7A | Short to GND in Passenger Side Airbag Variable Vent Hole Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the variable vent hole squib circuit for 0.5 seconds. ·
A variable vent hole squib malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 2 instrument panel wire ·
Instrument panel wire ·
Instrument panel passenger airbag assembly (Variable vent hole squib) ·
Airbag sensor assembly |
| B181D/7A | Short to B+ in Passenger Side Airbag Variable Vent Hole Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the variable vent hole squib circuit for 0.5 seconds. ·
A variable vent hole squib malfunction. ·
An airbag sensor assembly malfunction. |
·
No. 2 instrument panel wire ·
Instrument panel wire ·
Instrument panel passenger airbag assembly (Variable vent hole squib) ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSIS SYSTEM), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>CHECK MODE PROCEDURE).
| *1 | Variable Vent Hole Squib |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *4 | SST |
| *a | Front view of wire harness connector
(to Variable Vent Hole Squib) |
| *b | Color: Green |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the instrument panel passenger airbag assembly.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (green connector).
Never connect the tester to the instrument panel passenger airbag assembly (variable vent hole squib) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output |
| DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output |
Codes other than DTC B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
Disconnect the connectors from the airbag sensor assembly.
| *1 | Variable Vent Hole Squib |
| *2 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Variable Vent Hole Squib |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector
(to Variable Vent Hole Squib) |
| *b | Color: Green |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| b3-2 (VHP+) - Body ground | Ignition switch ON | Below 1 V |
| b3-1 (VHP-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b3-2 (VHP+) - b3-1 (VHP-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b3-2 (VHP+) - b3-1 (VHP-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b3-2 (VHP+) - Body ground | Always | 1 MΩ or higher |
| b3-1 (VHP-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Variable Vent Hole Squib |
| *2 | Airbag Sensor Assembly |
Restore the released activation prevention mechanism of connector B to its original condition.
Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output |
| DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output |
Codes other than DTC B181A/7A, B181B/7A, B181C/7A and B181D/7A may be output at this time, but they are not related to this check.
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is output
DTC B181A/7A, B181B/7A, B181C/7A or B181D/7A is not output
Restore the released activation prevention mechanism of connector B to its original condition.
| *1 | Variable Vent Hole Squib |
| *2 | No. 2 Instrument Panel Wire |
| *3 | Instrument Panel Wire |
| *4 | Airbag Sensor Assembly |
| *5 | Connector E |
| *a | Front view of wire harness connector
(to No. 2 Instrument Panel Wire) |
Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Gb3-1 (VHP+) - Body ground | Ignition switch ON | Below 1 V |
| Gb3-2 (VHP-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb3-1 (VHP+) - Gb3-2 (VHP-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb3-1 (VHP+) - Gb3-2 (VHP-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Gb3-1 (VHP+) - Body ground | Always | 1 MΩ or higher |
| Gb3-2 (VHP-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG