Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › OCCUPANT CLASSIFICATION SYSTEM › 2012.12–2014.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066373 OCCUPANT CLASSIFICATION SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  OCCUPANT CLASSIFICATION SYSTEM  B1788  Rear Occupant Classification Sensor RH Collision Detection  


DESCRIPTION

DTC B1788 is stored when the occupant detection ECU receives a collision detection signal, which is sent by the rear occupant classification sensor RH when an accident occurs.

DTC B1788 is also stored when the separate type front seat cushion spring assembly is subjected to a strong impact, even if an actual accident has not occurred.

However, when the occupant detection ECU outputs a collision detection signal, even if the vehicle has not been in a collision, DTC B1788 can be cleared by conducting the zero point calibration and sensitivity check.

Therefore, if DTC B1788 is output, first perform the zero point calibration and sensitivity check.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1788 Rear Occupant Classification Sensor RH Collision Detection
Either condition is met:
·

Occupant detection ECU receives a collision detection signal, which is sent by the rear occupant classification sensor RH when an accident occurs.

·

Separate type front seat cushion spring assembly is subjected to a strong impact, regardless of whether or not an actual accident has occurred.


·

Separate type front seat cushion spring assembly (Rear occupant classification sensor RH)

·

Occupant detection ECU



HINT:
·

When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1788 of the occupant classification system.

·

Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.



WIRING DIAGRAM

C256403E29
0.125,3.396 2.635,3.583 2.51,0.188 10 false Rear Occupant Classification Sensor RH 5.406,3.385 6.979,3.552 1.573,0.167 10 false Occupant Detection ECU 5.385,3.219 5.74,3.396 0.354,0.177 10 false d15 1.583,0.635 1.938,0.813 0.354,0.177 10 false 1 1.573,1.531 1.927,1.708 0.354,0.177 10 false 2 1.583,2.438 1.938,2.615 0.354,0.177 10 false 3 5.531,0.615 5.885,0.792 0.354,0.177 10 false 2 5.51,1.563 5.865,1.74 0.354,0.177 10 false 4 5.521,2.458 5.875,2.635 0.354,0.177 10 false 6 0.115,3.229 0.469,3.406 0.354,0.177 10 false d7

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1788 is not output
DTC B1788 is output


HINT:

DTCs other than DTC B1788 may be output at this time, but they are not related to this check.




DTC B1788 is not output

DTC B1788 is output

2.PERFORM ZERO POINT CALIBRATION
2.PERFORM ZERO POINT CALIBRATION

Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

3.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
3.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
4.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1788 is not output
DTC B1788 is output


HINT:

DTCs other than DTC B1788 may be output at this time, but they are not related to this check.




DTC B1788 is not output

END

DTC B1788 is output

5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
5.REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (REAR OCCUPANT CLASSIFICATION SENSOR RH)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the separate type front seat cushion spring assembly.



HINT:

Perform the inspection using parts from a normal vehicle when possible.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ZERO POINT CALIBRATION
6.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed
"Zero Point Calibration is complete." is not displayed



"Zero Point Calibration is complete." is displayed

7.PERFORM SENSITIVITY CHECK

"Zero Point Calibration is complete." is not displayed

9.REPLACE OCCUPANT DETECTION ECU
7.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
OK
NG



OK

8.CHECK DTC

NG

9.REPLACE OCCUPANT DETECTION ECU
8.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59
Result:
Proceed to
DTC B1788 is not output
DTC B1788 is output


HINT:

DTCs other than DTC B1788 may be output at this time, but they are not related to this check.




DTC B1788 is not output

END (SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY [REAR OCCUPANT CLASSIFICATION SENSOR RH] WAS DEFECTIVE)

DTC B1788 is output

9.REPLACE OCCUPANT DETECTION ECU
9.REPLACE OCCUPANT DETECTION ECU
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle when possible.



Result:
Proceed to
NEXT



NEXT

10.PERFORM ZERO POINT CALIBRATION
10.PERFORM ZERO POINT CALIBRATION
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.



Result:
Proceed to
"Zero Point Calibration is complete." is displayed



"Zero Point Calibration is complete." is displayed

11.PERFORM SENSITIVITY CHECK
11.PERFORM SENSITIVITY CHECK
a.

Perform the sensitivity check.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION

Standard:

27 to 33 kg (59.5 to 72.8 lb)



Result:
Proceed to
NEXT



NEXT

END (OCCUPANT DETECTION ECU WAS DEFECTIVE)