The airbag sensor assembly communication circuit consists of the occupant detection ECU and airbag sensor assembly.
DTC B1790 is stored when a malfunction is detected in the airbag sensor assembly communication circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1790 | Center Airbag Sensor Assembly Communication Circuit Malfunction | One of the following conditions is met:
·
Occupant detection ECU detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to +B signal in the airbag sensor assembly communication circuit for 2 seconds. ·
Airbag sensor assembly malfunction. ·
Occupant detection ECU malfunction. |
·
Floor wire ·
Front seat wire RH ·
Occupant detection ECU ·
Airbag sensor assembly |
When DTC B1650/32 is stored as a result of troubleshooting the airbag system, perform troubleshooting for DTC B1790 of the occupant classification system.
Use the GTS to check for DTCs of the occupant detection ECU, otherwise the DTCs cannot be read.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If troubleshooting (wire harness inspection) is difficult to perform, remove the front RH seat installation bolts to see the undersurface of the seat cushion.
In the above case, hold the seat so that it does not fall down. Holding the seat for a long period of time may cause problems, such as seat rail deformation. Hold the seat up only for as long as necessary.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1790 is not output |
| DTC B1790 is output |
DTCs other than DTC B1790 may be output at this time, but they are not related to this check.
DTC B1790 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1790 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant detection ECU and airbag sensor assembly.
| Proceed to |
|---|
| Connectors are properly connected |
| Connectors are not properly connected |
Connectors are properly connected
Connectors are not properly connected
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
Disconnect the connectors from the airbag sensor assembly and occupant detection ECU.
Check that the connectors (on the airbag sensor assembly side and occupant detection ECU side) are not damaged.
| Proceed to |
|---|
| Connectors are not deformed or damaged |
| Connectors are deformed or damaged |
Connectors are not deformed or damaged
Connectors are deformed or damaged
| *1 | Occupant Detection ECU |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *4 | Connector B |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| d16-7 - Body ground | Ignition switch ON | Below 1 V |
| d16-4 - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 9 (FSR+) and 17 (FSR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d16-7 - d16-4 | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d16-7 - d16-4 | Always | 1 MΩ or higher |
| d16-7 - Body ground | ||
| d16-4 - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the occupant detection ECU and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1790 is not output |
| DTC B1790 is output |
DTCs other than DTC B1790 may be output at this time, but they are not related to this check.
DTC B1790 is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DIAGNOSIS SYSTEM
DTC B1790 is output
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant detection ECU.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Perform the inspection using parts from a normal vehicle when possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Perform the zero point calibration.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
| Proceed to |
|---|
| "Zero Point Calibration is complete." is displayed |
"Zero Point Calibration is complete." is displayed
Perform the sensitivity check.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>INITIALIZATION
27 to 33 kg (59.5 to 72.8 lb)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.
Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1790 is not output |
| DTC B1790 is output |
DTCs other than DTC B1790 may be output at this time, but they are not related to this check.
DTC B1790 is not output
DTC B1790 is output
| *1 | Front Seat Wire RH |
| *2 | Floor Wire |
| *3 | Occupant Detection ECU |
| *4 | Airbag Sensor Assembly |
| *5 | Service Wire |
| *6 | Connector E |
| *7 | Connector D |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Front view of wire harness connector
(to Floor Wire) |
Disconnect the front seat wire RH connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Md1-1 - Body ground | Ignition switch ON | Below 1 V |
| Md1-5 - Body ground |
Turn the ignition switch off.
Disconnect the connector from the occupant detection ECU.
Using a service wire, connect terminals 7 and 4 of connector E.
Do not forcibly insert the service wire into the terminals of the connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Md1-1 - Md1-5 | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Md1-1 - Md1-5 | Always | 1 MΩ or higher |
| Md1-1 - Body ground | ||
| Md1-5 - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG