While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
·
ST NO. 1 relay circuit ·
Clutch start switch assembly ·
Ignition or starter switch assembly* ·
ECM |
Comes on | DTC stored |
*: w/o entry and start system
| DTC No. | Data List |
|---|---|
| P0617 | Starter Signal |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0617 | Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or higher |
Inspect the fuses of circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
| Condition | Starter Signal | Proceed to |
|---|---|---|
| Driving at 20 km/h (12.4 mph) or more | OFF | A |
| ON (w/ entry and start system) | B | |
| ON (w/o entry and start system) | C |
A
B
C
Repair or replace the harness or connector (ECM - clutch start switch assembly - engine stop and start ECU - certification ECU (smart key ECU assembly) - ST NO. 1 relay).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0617 is output | A |
| DTC is not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1AD-FTV STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector (ECM - clutch start switch assembly - engine stop and start ECU - ST relay).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1AD-FTV STARTING>IGNITION SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT