Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) › from 2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0103549 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) D

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  DIAGNOSIS SYSTEM  


PARKING ASSIST MONITOR DIAGNOSIS SYSTEM


a.

For parking assist monitor system diagnosis, signals received by the navigation receiver assembly (for navigation receiver type) or radio and display receiver assembly (for radio and display type) can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the navigation receiver assembly (for navigation receiver type) or radio and display receiver assembly (for radio and display type).

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>CALIBRATION


HINT:

The displayed items may differ depending on vehicle specifications.




DIAGNOSIS SCREEN TRANSITION


a.

During parking assist monitor system initialization

E286852
0.083,0.063 1.552,0.302 1.469,0.24 12 false Example: 2.979,1.031 4.5,1.25 1.521,0.219 10 false Start diagnostic mode

E286853


b.

After parking assist monitor system initialization

E286854
3.01,0.958 4.5,1.177 1.49,0.219 10 false Start diagnostic mode 0.073,0.063 1.542,0.302 1.469,0.24 12 false Example:

E286855



VEHICLE SIGNAL CHECK



b.
E273700

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


c.
E288888

Select "Vehicle Signal" on the "Function Check/Setting I" screen.


d.
E225776

Vehicle Signal Check Mode

i.

When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV" and "SPEED".

HINT:
·

Only conditions having inputs are displayed.

·

This screen displays vehicle signals input to the navigation receiver assembly*1 or radio and display receiver assembly*2.

*1: for Navigation Receiver Type

*2: for Radio and Display Type







CAR SIGNAL CHECK (parking assist monitor system input signals)


a.

Start diagnostic mode.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR

i.
E273700

Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.


ii.
E288889

Select "Camera Setting" on the "Function Check/Setting I" screen.

Parking Assist Monitor System Initialization Screen Transition
Not performed Car Signal Check screen
Performed Mode Setting Screen


iii.
E286851

When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.




b.
E286846

Car Signal Check

i.

On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

Item Inspection Detail Note
CAN CAN communication status signal input When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.

HINT:
·

When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.


·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".





c.

CAN inspection

HINT:

If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR





CALIBRATION WHEN SERVICING VEHICLE


NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>CALIBRATION