Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected When either condition below is met:
·

Stereo component amplifier assembly is/was not connected while the ignition switch is/was ON or ACC.

·

Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.


·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E263055E04
5.229,0.479 5.688,0.677 0.458,0.198 10 false M33 5.229,0.969 5.688,1.167 0.458,0.198 10 false M32 5.24,1.667 5.698,1.865 0.458,0.198 10 false M32 5.229,2.063 5.688,2.26 0.458,0.198 10 false M32 5.229,2.458 5.688,2.656 0.458,0.198 10 false M33 2.958,0.615 3.417,0.813 0.458,0.198 10 false AMP 2.948,1.115 3.406,1.313 0.458,0.198 10 false ACC 0.563,0.448 2.396,0.646 1.833,0.198 10 false from Battery 0.354,0.948 2.5,1.146 2.146,0.198 10 false from ACC Relay 5.313,0.25 5.469,0.448 0.156,0.198 10 false 1 5.281,0.75 5.594,0.948 0.313,0.198 10 false 12 5.323,1.469 5.479,1.667 0.156,0.198 10 false 8 5.333,1.865 5.49,2.063 0.156,0.198 10 false 7 5.323,2.26 5.479,2.458 0.156,0.198 10 false 3 3.198,1.656 3.813,1.854 0.615,0.198 10 false TX1+ 3.219,2.042 3.833,2.24 0.615,0.198 10 false TX1- 3.625,1.563 3.781,1.76 0.156,0.198 10 false 7 3.635,1.938 3.948,2.135 0.313,0.198 10 false 8 2.604,2.594 3.063,2.792 0.458,0.198 10 false G143 2.625,2.781 3.865,3.188 1.24,0.406 10 false Radio and Display Receiver Assembly 5.479,2.969 6.76,3.375 1.281,0.406 10 false Stereo Component Amplifier Assembly 5.635,0.469 5.948,0.667 0.313,0.198 10 false +B 5.677,0.969 6.135,1.167 0.458,0.198 10 false ACC 5.667,1.667 6.125,1.865 0.458,0.198 10 false TX+ 5.667,2.052 6.125,2.25 0.458,0.198 10 false TX- 5.667,2.458 6.125,2.656 0.458,0.198 10 false GND 0.708,3.417 2.75,3.635 2.042,0.219 10 false : AVC-LAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

DTC B15C3 is not output.



Result:
Proceed to
OK
NG



OK

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

NG

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed A
Optional components (including associated wiring) are not installed B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK FOR DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (OPTIONAL COMPONENTS [INCLUDING ASSOCIATED WIRING] IS DEFECTIVE)

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E271825C02
1.49,0.052 2,0.302 0.51,0.25 1.844,1.74 2.354,2 0.51,0.26 0.896,2.365 1,1.917 1,1.917 1.25,1.917 true 0.365,1.979 0.531,1.979 0.531,1.979 0.604,2.365 true 2.635,0.885 2.75,0.417 2.75,0.417 3,0.417 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.615,0.094 1.927,0.271 0.313,0.177 10 false M32 1.969,1.792 2.281,2.01 0.313,0.219 10 false M33 1.292,1.833 1.635,2.042 0.344,0.208 10 false GND 0.135,1.896 0.375,2.115 0.24,0.219 10 false +B 3.042,0.333 3.396,0.542 0.354,0.208 10 false ACC
*a Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


Disconnect the stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-1 (+B) - Body ground Always 11 to 14 V
M32-12 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the G143 radio and display receiver assembly connector.


b.

Disconnect the M32 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-7 (TX1+) - M32-8 (TX+) Always Below 1 Ω
G143-8 (TX1-) - M32-7 (TX-) Always Below 1 Ω
G143-7 (TX1+) - Body ground Always 10 kΩ or higher
G143-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY