Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2016.08
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the audio and visual system connected to the AVC-LAN (communication bus) transfers switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the audio and visual system will not function normally because communication is not possible.

WIRING DIAGRAM

E280962E05
2.469,0.438 2.625,0.635 0.156,0.198 10 false 8 2.49,1.229 2.646,1.427 0.156,0.198 10 false 7 5.635,0.406 5.792,0.604 0.156,0.198 10 false 7 5.667,1.188 5.823,1.385 0.156,0.198 10 false 8 2.094,0.552 2.396,0.75 0.302,0.198 10 false TX+ 2.094,1.365 2.396,1.563 0.302,0.198 10 false TX- 5.865,1.385 6.365,1.625 0.5,0.24 10 false TX1- 5.865,0.573 6.49,0.813 0.625,0.24 10 false TX1+ 5.74,1.917 6.24,2.156 0.5,0.24 10 false G143 5.75,2.115 6.979,2.51 1.229,0.396 10 false Radio and Display Receiver Assembly 1.198,1.896 1.698,2.135 0.5,0.24 10 false M32 1.219,2.063 3.625,2.271 2.406,0.208 10 false Stereo Component Amplifier Assembly 0.875,2.385 3.281,2.594 2.406,0.208 10 false : AVC-LAN communication Line

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly with the connector(s) still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E280968E01
1.74,0.958 1.583,0.417 1.583,0.417 1.333,0.417 true 1.854,0.938 2.094,0.417 2.094,0.417 2.344,0.417 true 1.031,0.333 1.448,0.51 0.417,0.177 10 false TX1- 2.406,0.333 2.823,0.51 0.417,0.177 10 false TX1+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the M32 stereo component amplifier assembly connector.


b.

Disconnect the G143 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-8 (TX+) - G143-7 (TX1+) Always Below 1 Ω
M32-7 (TX-) - G143-8 (TX1-) Always Below 1 Ω
M32-8 (TX+) - Body ground Always 10 kΩ or higher
M32-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY